REL-FO/LRC-230AC/2X21/MS - Single relay Phoenix Contact

Mã sản phẩm: 1308330

Danh mục: PHOENIX CONTACT, Switch, Measure and Monitor Phoenix Contact,

Plug-in miniature relay with mechanical switching position indicator, FASTON connection, 2 changeover contacts, status display: Yellow LED, Freewheeling diode, RC element, Input voltage: 230 V AC

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

General	Do not use to separate SELV/PELV circuits from other circuits, because safe isolation is not guaranteed. (applies to the optocoupler variants)
General	The outputs are not suitable for switching different outer conductors.
General	The system installer must ensure the touch protection of the product (at voltages > 25 V AC/60 V DC). The product is a built-in device without protection against direct contact.

Product type	Single relay
Product family	ESSENTIAL edition
Operating mode	100% operating factor
Mechanical service life	approx. 3x 10⁷ cycles
Relay type	Electromechanical relay
Insulation characteristics: Air clearances and creepage distances between the power circuits
Insulation	Basic insulation
Overvoltage category	II
Pollution degree	3

Maximum power dissipation for nominal condition	1 W
Test voltage (Winding/contact)	5 kV_rms (50 Hz, 1 min., winding/contact)
Test voltage (Changeover contact/changeover contact)	3 kV_rms (50 Hz, 1 min., changeover contact/changeover contact)
Test voltage ()	1 kV_rms (50 Hz, 1 min., open contact)
Air clearances and creepage distances between the power circuits
Rated insulation voltage	250 V AC
Rated surge voltage	2.5 kV

Coil side
Nominal input voltage U_N	230 V AC
Input voltage range	184 V AC ... 253 V AC
Mains frequency	50/60 Hz
Typical input current at U_N	4.5 mA (50 Hz)
Input power dissipation for U_N	1 W
Typical response time	2 ms ... 15 ms
Typical release time range	5 ms ... 20 ms
Protective circuit	Freewheeling diode
Protective circuit		RC element
Status display	Yellow LED
Coil resistance	24100 Ω ±10 %

Switching
Contact type	2 changeover contacts
Type of switch contact	Single contact
Drive and function	monostable
Drive (polarity)	bipolar
Contact material	AgSnO
Maximum switching voltage	250 V AC/DC
Minimum switching voltage	5 V (10 mA)
Limiting continuous current	8 A
Maximum inrush current	16 A (20 ms, N/O contacts)
Inrush current, minimum	10 mA (5 V)
Interrupting rating (ohmic load) max.	192 W (24 V DC)
		240 W (30 V DC)
		2000 VA (250 V AC)

Connection method

FASTON connection

Width	13 mm
Height	31.1 mm
Depth	34 mm

Ambient conditions
Degree of protection (Relay)	RT II (Relay)
Degree of protection (Installation location)	IP54 (Installation location)
Ambient temperature (operation)	-40 °C ... 70 °C
Ambient temperature (storage/transport)	-40 °C ... 70 °C
Altitude	≤ 2000 m

Standards/regulations	IEC 61810-1
Standards/regulations		IEC 60664-1
Air clearances and creepage distances between the power circuits
Standards/regulations	IEC 60664-1