PSR-SPP- 24DC/TS/S - Safety module Phoenix Contact

Mã sản phẩm: 2986232

Danh mục: PHOENIX CONTACT, Switch, Measure and Monitor Phoenix Contact,

Freely configurable safety module with 20 safe inputs and 4 safe outputs, 4 signal, 2 clock, and 2 ground switching outputs, diagnostics possible via bus gateways, up to SIL 3, Cat. 4/PL e, SIL 3, EN 50156, pluggable Push-in terminal block

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

Product type	Safety device
Application	Emergency stop
		Light grid
		Safety door
		Two-hand control
Number of possible extension modules	1 (max. continuous current via PSR-TBUS: 4 A)
Insulation characteristics: Air clearances and creepage distances between the power circuits
Overvoltage category	III
Pollution degree	2
Times
Response time	max. 30 ms (plus response time of PSR-TS-SDOR4)
Recovery time	< 10 s

Maximum power dissipation for nominal condition	6372 mW (at a = 20, b = 2, c = 4, e = 2, I_clock = 100 mA, I_signal = 100 mA, I_Out/GND = 2 A, I_Out/Out = 2 A)
Nominal operating mode	100% operating factor
Interfaces	USB
Interfaces		DIN rail TBUS for extension modules and bus couplers
Supply
Rated control circuit supply voltage U_S	18 V DC ... 30 V DC (Incl. all tolerances, incl. residual ripple)
Rated control circuit supply voltage U_S	24 V DC (A1/A2)
Rated control supply current I_S	typ. 110 mA
Limiting continuous current	max. 6 A (For looped-through current paths A1/A1 and A2/A2)
Filter time	typ. 20 ms (Load-dependent, in the event of voltage dips at U_S)
Protective circuit	Yes, within the scope of the operating voltage limits
Status display	3x LED green, 1x LED red

Digital
Description of the input	Digital, type HTL
Number of inputs	10 (Two-channel, up to SIL 3)
Number of inputs		20 (Single-channel, up to SIL 2)
Input voltage range "0" signal	0 V DC ... 5 V DC (for safe Off)
Input voltage range "1" signal	11 V DC ... 30 V DC
Cable length	max. 2000 m
Status display	20 x LED green (1 LED per input)
Current consumption	typ. 4 mA

Digital
Number of outputs	4 (Safe semiconductor outputs, up to Cat. 4 in accordance with EN ISO 13849-1)
Number of outputs		2 (Ground switching outputs)
Note on protection circuit	Yes, within the scope of the operating voltage limits
Short-circuit protection	Yes
Output voltage	< 5 V (Low state)
Leakage current	max. 2 mA
Max. capacitive load	max. 1 µF (Electronic components)
Max. inductive load	See "Protective circuit"
Limiting continuous current	2 A (Per channel, see Derating)
Limiting continuous current		2 A (Total current of all outputs)
Nominal output voltage	24 V DC (Supply via 24 V/0 V)
Nominal output voltage range	18 V DC ... 30 V DC (Incl. all tolerances, incl. residual ripple)
Status display	4 x LED green (1 LED per output)
Test pulses	< 1 ms
Signal
Output description	Digital
Number of outputs	4
Voltage	24 V DC (Supply via 24 V/0 V)
Limiting continuous current	100 mA
Short-circuit protection	Yes
Clock
Output description	Digital
Number of outputs	2
Voltage	24 V DC (Supply via 24 V/0 V)
Limiting continuous current	100 mA
Test pulses	< 1 ms
Short-circuit protection	Yes

Connection technology
pluggable	yes
Conductor connection
Connection method	Push-in connection
Conductor cross section rigid	0.2 mm² ... 1.5 mm²
Conductor cross section, flexible, with ferrule, with plastic sleeve	0.25 mm² ... 1.5 mm² (only together with CRIMPFOX 6)
Conductor cross section flexible, with ferrule without plastic sleeve	0.25 mm² ... 1.5 mm² (only together with CRIMPFOX 6)
Conductor cross-section AWG	24 ... 16
Stripping length	8 mm

Width	67.5 mm
Height	112 mm
Depth	114.5 mm

Color	yellow
Housing material	Polyamide PA non-reinforced

Safety data
Stop category	0
Safety data: EN ISO 13849
Category	2 (1-channel parameterization)
Category		4 (2-channel parameterization)
Performance level (PL)	d (1-channel parameterization)
Performance level (PL)		e (2-channel parameterization)
Safety data: EN 50156
Safety Integrity Level (SIL)	max. 3 (Reference IEC 61508)
Safety data: IEC 61508 - High demand
Safety Integrity Level (SIL)	2 (1-channel parameterization)
Safety Integrity Level (SIL)		3 (2-channel parameterization)
Proof test interval	240 Months
Duration of use	240 Months
Safety data: IEC 61508 - Low demand
Safety Integrity Level (SIL)	2 (1-channel parameterization)
Proof test interval	240 Months
Duration of use	240 Months

Ambient conditions
Degree of protection	IP20
Min. degree of protection of inst. location	IP54
Ambient temperature (operation)	-20 °C ... 55 °C
Ambient temperature (storage/transport)	-20 °C ... 70 °C
Maximum altitude	max. 2000 m (See Appendix "Using PSR-TRISAFE modules at altitudes greater than 2000 m above sea level")
Max. permissible humidity (storage/transport)	75 % (On average, 85 % occasionally)
Max. permissible relative humidity (operation)	75 % (On average, 85 % occasionally)
Shock (operation)	10g (Δt = 11 ms, three shocks in each space direction)
Shock (operation)		10g (Δt = 16 ms, continuous shock, 1000 shocks in each space direction)
Vibration (operation)	2g
Air pressure (operation)	70 kPa ... 108 kPa (up to 3000 m above sea level)
Air pressure (storage/transport)	66 kPa ... 108 kPa (up to 3500 m above sea level)