PSR-SPP- 24DC/ESD/5X1/1X2/T10S - Safety relays Phoenix Contact

Mã sản phẩm: 2981509

Danh mục: PHOENIX CONTACT, Switch, Measure and Monitor Phoenix Contact,

Safety relay for emergency stop and safety door monitoring up to SIL 3 or Cat. 4, PL e in accordance with EN ISO 13849, automatic or manual activation, 3 N/O contacts, 1 N/C contact, 2 N/O contacts with a fixed dropout delay of 10 s, pluggable Push-in terminal block

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

Product type	Safety relays
Product family	PSRclassic
Application	Emergency stop
		Safety door
		Light grid
Mechanical service life	10x 10⁶ cycles
Relay type	Electromechanical relay with force-guided contacts in accordance with IEC/EN 61810-3

Maximum power dissipation for nominal condition	3.6 W
Nominal operating mode	100% operating factor
Air clearances and creepage distances between the power circuits
Rated insulation voltage	250 V AC
Rated surge voltage/insulation	Basic insulation 4 kV: between all current paths and housing Safe isolation, reinforced insulation 6 kV: between 13/14, 23/24, 33/34, and the remaining current paths between 13/14, 23/24, 33/34 among one another
Supply
Rated control circuit supply voltage U_S	20.4 V DC ... 26.4 V DC
Rated control circuit supply voltage U_S	24 V DC -15 % / +10 %

General
Power consumption at U_S	typ. 3.6 W
Rated control supply current I_S	typ. 150 mA
Inrush current	200 mA (at U_S)
		< 40 mA (with U_s/I_xto S10)
		< 150 mA (with U_s/I_xto S12)
		> -60 mA (with U_s/I_xto S22)
		< 40 mA (with U_s/I_xto S34)
		< 40 mA (with U_s/I_xto S35)
Current consumption	< 40 mA (with U_s/I_xto S10)
		< 40 mA (with U_s/I_xto S12)
		> -40 mA (with U_s/I_xto S22)
		0 mA (with U_s/I_xto S34)
		< 5 mA (with U_s/I_xto S35)
Voltage at input/start and feedback circuit	24 V DC -15 % / +10 %
Filter time	1 ms (at A1 in the event of voltage dips at U_s)
		max. 1.5 ms (at S10, S12; test pulse width)
		7.5 ms (at S10, S12; test pulse rate)
		Test pulse rate = 5 x Test pulse width
Typical response time	< 600 ms (automatic start)
Typical response time		< 70 ms (manual start)
Typ. starting time with U_s	< 600 ms (when controlled via A1)
Typical release time	< 20 ms (when controlled via S11/S12 and S21/S22)
Typical release time		< 20 ms (when controlled via A1)
Concurrence	∞
Recovery time	< 1 s
Delay time	K3(t), K4(t) fixed depending on model
Maximum switching frequency	0.5 Hz
Protective circuit	Surge protection; Suppressor diode
Max. permissible overall conductor resistance	approx. 11 Ω (Input and start circuits at U_S)
Operating voltage display	1 x green LED
Status display	4 x green LEDs

Contact type	5 enabling current paths
Contact type		1 signaling current path
Contact material	AgSnO₂
Maximum switching voltage	250 V AC/DC (Observe the load curve)
Minimum switching voltage	5 V AC/DC
Limiting continuous current	6 A (N/O contact, pay attention to the derating)
Limiting continuous current		6 A (N/C contact)
Maximum inrush current	20 A (Δt  100 ms, undelayed contacts)
Maximum inrush current		8 A (delayed contacts)
Inrush current, minimum	10 mA
Sq. Total current	55 A² (observe derating)
Interrupting rating (ohmic load) max.	144 W (24 V DC, τ = 0 ms)
		288 W (48 V DC, τ = 0 ms)
		110 W (110 V DC, τ = 0 ms, delayed contacts: 77 W)
		88 W (220 V DC, τ = 0 ms)
		1500 VA (250 V AC, τ = 0 ms, delayed contacts: 2000 VA)
Maximum interrupting rating (inductive load)	42 W (24 V DC, τ = 40 ms, delayed contacts: 48 W)
		42 W (48 V DC, τ = 40 ms, delayed contacts: 40 W)
		42 W (110 V DC, τ = 40 ms, delayed contacts: 35 W)
		42 W (220 V DC, τ = 40 ms, delayed contacts: 33 W)
Switching capacity min.	50 mW
Switching capacity (360/h cycles)	4 A (24 V DC)
Switching capacity (360/h cycles)		4 A (230 V AC)
Switching capacity (3600/h cycles)	2.5 A (24 V (DC13))
Switching capacity (3600/h cycles)		3 A (230 V (AC15))
Output fuse	10 A gL/gG (N/O contact)
Output fuse		6 A gL/gG (N/C contact)

Connection technology
pluggable	yes
Conductor connection
Connection method	Push-in connection
Conductor cross section rigid	0.2 mm² ... 1.5 mm²
Conductor cross section flexible	0.2 mm² ... 1.5 mm²
Conductor cross section, flexible, with ferrule, with plastic sleeve	0.25 mm² ... 1.5 mm² (only together with CRIMPFOX 6)
Conductor cross section flexible, with ferrule without plastic sleeve	0.25 mm² ... 1.5 mm² (only together with CRIMPFOX 6)
Conductor cross-section AWG	24 ... 16
Stripping length	8 mm

Width	45 mm
Height	112 mm
Depth	114.5 mm

Housing material

Polyamide

Safety data
Stop category	0
Stop category		1
Safety data: EN ISO 13849
Category	4 (Undelayed contacts)
Category		3 (delayed contacts)
Performance level (PL)	e (for delayed contacts PL d)
Safety data: IEC 61508 - High demand
Equipment type	Type A
Safety Integrity Level (SIL)	3 (for delayed contacts SIL 2)
Probability of a hazardous failure per hour (PFH_D)	1.67 x 10^-9
Proof test interval	240 Months
Duration of use	240 Months
Safety data: IEC 61508 - Low demand
Equipment type	Type A
Safety Integrity Level (SIL)	3 (for delayed contacts SIL 2)
Probability of a hazardous failure on demand (PFD_AVG)	1.41 x 10^-4
Proof test interval	19 Months
Duration of use	240 Months

Ambient conditions
Degree of protection	IP20
Min. degree of protection of inst. location	IP54
Ambient temperature (operation)	-20 °C ... 55 °C (observe derating)
Ambient temperature (storage/transport)	-40 °C ... 70 °C
Maximum altitude	≤ 2000 m (Above sea level)
Max. permissible humidity (storage/transport)	75 % (on average, 85% infrequently, non-condensing)
Max. permissible relative humidity (operation)	75 % (on average, 85% infrequently, non-condensing)
Shock	15g
Vibration (operation)	10 Hz ... 150 Hz, 2g