PSR-SCP- 24DC/FSP/1X1/1X2 - Coupling relay Phoenix Contact

Mã sản phẩm: 2981978

Danh mục: PHOENIX CONTACT, Switch, Measure and Monitor Phoenix Contact,

Safe coupling relay for SIL 3 high- and low-demand applications, couples digital output signals to the periphery, one enabling current path, one signal contact, module for safe state off applications, test pulse filter, fuse, plug-in screw connection, width: 17.5 mm

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

Product type	Coupling relay
Product family	PSRclassic
Application	Safe switch off
		High demand
		Low demand
Mechanical service life	10x 10⁶ cycles
Relay type	Electromechanical relay with force-guided contacts in accordance with IEC/EN 61810-3

Maximum power dissipation for nominal condition	2.4 W
Nominal operating mode	100% operating factor
Air clearances and creepage distances between the power circuits
Rated insulation voltage	250 V AC
Rated surge voltage/insulation	Safe isolation, reinforced insulation 6 kV between the control circuits (A1/A2), (21/22), (13/14)

General
Rated control circuit supply voltage U_S	24 V DC -15 % / +10 %
Power consumption at U_S	typ. 1.32 W
Rated control supply current I_S	typ. 55 mA
Input voltage range	20.4 V DC ... 26.4 V DC
Inrush current	max. 100 mA
Filter time	max. 5 ms (at A1 in the event of voltage dips at U_s)
		max. 2 ms (Test pulse width; high test pulse at A1/A2)
		≥ 100 ms (Test pulse width; high test pulse at A1/A2)
		Test pulse rate = 80 x Test pulse width
		max. 5 ms (Test pulse width; low test pulse at A1/A2)
		≥ 50 ms (Test pulse rate; low test pulse at A1/A2)
		Test pulse rate = 15 x Test pulse width
Typ. starting time with U_s	50 ms
Typical release time	50 ms
Recovery time	1 s
Maximum switching frequency	0.5 Hz
Protective circuit	Surge protection; Suppressor diode, 33 V (A1 - A2)
Operating voltage display	1 x yellow LED

Contact type	1 enabling current path
Contact type		1 confirmation current path
Contact material	AgCuNi, + 0.2 µm Au
Maximum switching voltage	250 V AC/DC (N/O contact / N/C contact, observe the load curve)
Minimum switching voltage	15 V AC/DC (N/O contact / N/C contact)
Limiting continuous current	5 A (N/O contact, pay attention to the derating)
Limiting continuous current		100 mA (N/C contact)
Maximum inrush current	5 A (N/O contact)
Maximum inrush current		100 mA (N/C contact)
Inrush current, minimum	5 mA (N/O contact / N/C contact)
Sq. Total current	25 A² (observe derating)
Interrupting rating (ohmic load) max.	120 W (24 V DC, τ = 0 ms, N/C contact: 2.4 W)
		192 W (48 V DC, τ = 0 ms, N/C contact: 4.8 W)
		162 W (60 V DC, τ = 0 ms, N/C contact: 6 W)
		66 W (110 V DC, τ = 0 ms, N/C contact: 11 W)
		60 W (220 V DC, τ = 0 ms, N/C contact: 22 W)
		1250 VA (250 V AC, τ = 0 ms, N/C contact: 25 VA)
Maximum interrupting rating (inductive load)	72 W (24 V DC, τ = 40 ms, N/C contact: 2.4 W)
		43 W (48 V DC, τ = 40 ms, N/C contact: 4.8 W)
		41 W (60 V DC, τ = 40 ms, N/C contact: 6 W)
		35 W (110 V DC, τ = 40 ms, N/C contact: 11 W)
		48 W (220 V DC, τ = 40 ms, N/C contact: 22 W)
Switching capacity	min. 75 mW
Switching capacity (3600/h cycles)	5 A (24 V (DC13))
Switching capacity (3600/h cycles)		5 A (230 V (AC15))
Output fuse	5 A T fuse (N/O contact)
Output fuse		150 mA Fast-blow (N/C contact)

Connection technology
pluggable	yes
Conductor connection
Connection method	Screw connection
Conductor cross section rigid	0.2 mm² ... 2.5 mm²
Conductor cross section flexible	0.2 mm² ... 2.5 mm²
Conductor cross-section AWG	24 ... 12
Stripping length	7 mm
Screw thread	M3

Width	17.5 mm
Height	99 mm
Depth	114.5 mm

Housing material

Polyamide

Safety data
Stop category	0
Safety data: EN ISO 13849
Category	4 (Diagnostic coverage (DC) of the control unit at A1/A2 must be ≥ 99%)
Performance level (PL)	e (Diagnostic coverage (DC) of the control unit at A1/A2 must be ≥ 99%)
Safety data: EN 50156
Safety Integrity Level (SIL)	3
Safety data: IEC 61508 - High demand
Equipment type	Type A
Safety Integrity Level (SIL)	3 (max. 10% of the entire SIL; diagnostic coverage (DC) of the control unit at A1/A2 must be ≥ 90% )
Safe Failure Fraction (SFF)	99.99 %
MTBF	319 Years (includes errors which are not part of the safety function; MTTR = 8 h)
λ_SU	62.7 FIT
λ_SD	198 FIT
λ_DU	0.02 FIT
λ_DD	3.66 FIT
Probability of a hazardous failure per hour (PFH_D)	2.02 x 10^-11 (4 A DC13; 5 A AC15; 8760 switching cycles/year)
Diagnostic coverage (DC)	99 % (during evaluation of the confirmation current path)
Proof test interval	240 Months
Duration of use	240 Months
Safety data: IEC 61508 - Low demand
Designation	The safety characteristic data is calculated assuming an average ambient temperature of 40°C. At higher ambient temperatures, a safety factor of 1.8 should be applied to the characteristics.
Equipment type	Type A
Safety Integrity Level (SIL)	3 (max. 10% of the entire SIL; diagnostic coverage (DC) of the control unit at A1/A2 must be ≥ 90% )
Safe Failure Fraction (SFF)	99.77 %
MTBF	113 Years (includes errors which are not part of the safety function; MTTR = 8 h)
λ_SU	909.7 FIT
λ_SD	0 FIT
λ_DU	2.09 FIT
λ_DD	0 FIT
Probability of a hazardous failure on demand (PFD_AVG)	9.87 x 10^-5
Probability of a hazardous failure on demand (PFD_AVG)		9.15 x 10^-6 (for proof test interval = 1 year)
Proof test interval	144 Months
Duration of use	240 Months

Ambient conditions
Degree of protection	IP20
Min. degree of protection of inst. location	IP54
Ambient temperature (operation)	-20 °C ... 55 °C (observe derating)
Ambient temperature (storage/transport)	-40 °C ... 70 °C
Maximum altitude	≤ 2000 m (Above sea level)
Max. permissible humidity (storage/transport)	75 % (on average, 85% infrequently, non-condensing)
Max. permissible relative humidity (operation)	75 % (on average, 85% infrequently, non-condensing)
Shock	15g
Vibration (operation)	10 Hz ... 150 Hz, 2g