PSR-PS23-1NO-1NC-24VDC-SC - Coupling relay Phoenix Contact

Mã sản phẩm: 2702663

Danh mục: PHOENIX CONTACT, Switch, Measure and Monitor Phoenix Contact,

Coupling relay for SIL 3 high and low-demand applications, couples digital output signals to the I/O, 1 enabling current path, 1 confirmation current path, safe state off applications, test pulse filter, fixed screw terminal block

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

Utilization restriction
CCCex note	Use in potentially explosive areas is not permitted in China.

Product type	Coupling relay
Product family	PSRmini
Application	Safe switch off
		High demand
		Low demand
		Ex
Mechanical service life	10x 10⁶ cycles
Relay type	Electromechanical relay with force-guided contacts in accordance with IEC/EN 61810-3
Times
Typ. starting time with U_s	< 70 ms (with U_s when controlled via A1)
Typical release time	< 10 ms (when controlled via A1)
Recovery time	500 ms

Maximum power dissipation for nominal condition	3.49 W (I_L² = 36 A²)
Nominal operating mode	100% operating factor
Air clearances and creepage distances between the power circuits
Rated insulation voltage	250 V AC
Rated surge voltage/insulation	Basic insulation 4 kV between all current paths and housing
Rated surge voltage/insulation		Safe isolation, 6 kV reinforced insulation from the control circuit and confirmation current path to the enabling current path
Supply
Rated control circuit supply voltage U_S	19.2 V DC ... 30 V DC
Rated control circuit supply voltage U_S	24 V DC -20 % / +25 % (A1/A2)
Rated control supply current I_S	typ. 45 mA
Power consumption at U_S	typ. 1.08 W
Inrush current	typ. 120 mA (Δt <10 ms at U_s)
Filter time	max. 2 ms (at A1-A2 in the event of voltage dips at U_s)
		max. 2 ms (at A1-A2; low test pulse width)
		> 30 ms (at A1-A2; low test pulse rate)
		max. 2 ms (at A1-A2; high test pulse width)
		> 1 s (at A1-A2; high test pulse rate)
Protective circuit	Serial protection against polarity reversal; 35 V suppressor diode (A1-A2)

Relay: Enabling current path
Output description	2 N/O contacts in series, without delay, floating
Number of outputs	1 (safety-related N/O contacts: 13/14)
Contact type	1 enabling current path
Contact material	AgSnO₂
Switching voltage	min. 12 V AC/DC
Switching voltage		max. 250 V AC/DC (Observe the load curve)
Switching capacity	min. 60 mW
Inrush current	min. 3 mA
Inrush current		max. 6 A
Switching capacity in accordance with IEC 60947-5-1	4 A (24 V (DC13))
Switching capacity in accordance with IEC 60947-5-1		5 A (250 V (AC15))
Limiting continuous current	6 A (High demand)
Limiting continuous current		4 A (Low demand)
Sq. Total current	36 A² (observe derating)
Switching frequency	max. 1 Hz
Mechanical service life	10x 10⁶ cycles
Output fuse	6 A gL/gG
Output fuse		4 A gL/gG (for low-demand applications)
Relay: Confirmation current path
Output description	2 N/C contacts in series, without delay, floating
Number of outputs	1 (safety-related N/C contacts: 21/22)
Contact type	1 confirmation current path
Contact material	AgCuNi, + Au
Switching voltage	min. 5 V DC
Switching voltage		max. 30 V DC
Switching capacity	min. 20 mW
Inrush current	min. 1 mA
Inrush current		max. 100 mA
Limiting continuous current	100 mA
Switching frequency	max. 1 Hz
Mechanical service life	10x 10⁶ cycles
Output fuse	150 mA Fast-blow

Connection technology
pluggable	no
Conductor connection
Connection method	Screw connection
Conductor cross section rigid	0.2 mm² ... 2.5 mm²
Conductor cross section flexible	0.2 mm² ... 2.5 mm²
Conductor cross-section AWG	24 ... 12
Stripping length	12 mm
Screw thread	M3
Tightening torque	0.5 Nm ... 0.6 Nm

Status display	1 x green LED
Operating voltage display	1 x yellow LED

Width	6.8 mm
Height	93.1 mm
Depth	102.5 mm

Housing material

PBT

Safety data
Stop category	0
Safety data: EN 50156-2
Safety Integrity Level (SIL)	3 (Reference IEC 61508)
Safety data: IEC 61508 - High demand
Designation	For use in high-demand applications, the diagnostics function must be implemented via the confirmation current path.
Equipment type	Type A
Safety Integrity Level (SIL)	3
Safe Failure Fraction (SFF)	99.996 %
MTBF	40.09 Years
λ_SU	2765,12 FIT
λ_SD	0 FIT
λ_DU	0.11 FIT
λ_DD	5.45 FIT
Probability of a hazardous failure per hour (PFH_D)	1.00 x 10^-9 (4 A DC13; 5 A AC15; 8760 switching cycles/year)
Proof test interval	240 Months
Duration of use	240 Months
Safety data: IEC 61508 - Low demand
Equipment type	Type A
Safety Integrity Level (SIL)	3
Safe Failure Fraction (SFF)	99.833 %
MTBF	43.48 Years
λ_SU	2546,42 FIT
λ_SD	0 FIT
λ_DU	4.26 FIT
λ_DD	0 FIT
Probability of a hazardous failure on demand (PFD_AVG)	1.36 x 10^-4 (4 A DC13; 5 A AC15)
Probability of a hazardous failure on demand (PFD_AVG)		1.87 x 10^-5 (for proof test interval = 1 year)
Proof test interval	72 Months
Duration of use	240 Months

Ambient conditions
Degree of protection	IP20
Min. degree of protection of inst. location	IP54
Ambient temperature (operation)	-40 °C ... 70 °C (observe derating)
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Maximum altitude	≤ 2000 m (Above sea level)
Max. permissible humidity (storage/transport)	75 % (on average, 85% infrequently, non-condensing)
Max. permissible relative humidity (operation)	75 % (on average, 85% infrequently, non-condensing)
Shock	15g
Vibration (operation)	10 Hz ... 150 Hz, 2g

ATEX
Identification	 II 3G Ex ec nC IIC T4 Gc
Certificate	UL 22 ATEX 2912X
IECEx
Identification	Ex ec nC IIC T4 Gc
Certificate	IECEx UL 22.0037X
UL, USA/Canada
Identification	cULus
Certificate	E140324
UL Ex, USA / Canada
Identification	Class I, Zone 2, AEx nA nC IIC T4 / Ex nA nC IIC Gc T4 X
Identification		Class I, Div. 2, Groups A, B, C, D, T4
Certificate	E360692
CE
Identification	CE-compliant
Certificate	CE-compliant
Note	The full EC declaration of conformity can be downloaded via the item at phoenixcontact.net/products.
Environmental simulation test
Certificate	ISA-S71.04 (G3)