PSR-MM30-2NO-2DO-24DC-SP - Safety device Phoenix Contact

Mã sản phẩm: 2702358

Danh mục: PHOENIX CONTACT, Switch, Measure and Monitor Phoenix Contact,

2-channel over-speed and zero-speed safety relay up to SIL 3, Cat. 4, PL e, 2 safe relay outputs, suitable for connecting HTL, TTL, or sine/cosine encoders as well as proximity switches, plug-in Push-in terminal block, width: 22.5 mm

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

Product type	Safety device
Application	Zero-speed safety relay
Application		Over-speed safety relay
Relay type	Electromechanical relay with force-guided contacts in accordance with IEC/EN 61810-3
Times
Typical response time	< 200 ms (For U_sautostart)
Typical response time		< 150 ms (For U_smanual, monitored start)
Delay time range	0 s ... 10 s ±10 % (Adjustable switch-on delay for downtime contacts 23/24)
Restart time	< 1 s (Boot time)
Recovery time	< 1 s

Maximum power dissipation for nominal condition	6.5 W (at U_S = 26.4 V, U_INPUT =30 V, I_L² = 72 A²)
Nominal operating mode	100% operating factor
Interfaces	Encoder
Interfaces		Proximity switches
Air clearances and creepage distances between the power circuits
Rated insulation voltage	250 V AC
Rated surge voltage/insulation	Basic insulation 4 kV between all current paths and housing
Rated surge voltage/insulation		Safe isolation, reinforced insulation 6 kV between input circuit (A1/A2, I1, I2, I3, MI1, MI2, IN1, IN2, S34, MO1, MO2, RJ45, USB) and the enabling current paths (13/14, 23/24)
Supply
Designation	A1/A2
Rated control circuit supply voltage U_S	20.4 V DC ... 26.4 V DC
Rated control circuit supply voltage U_S	24 V DC -15 % / +10 %
Rated control supply current I_S	typ. 74 mA
Power consumption at U_S	typ. 1.78 W
Inrush current	< 18 A (Δt = 500 µs at U_s)
Filter time	2 ms (at A1 in the event of voltage dips at U_s)
Protective circuit	Serial protection against polarity reversal; 33 V suppressor diode

Digital: Operating mode and monitoring inputs
Description of the input	NPN, IEC 61131-2, type 1
Number of inputs	1 (Non-safety-related start input: S34)
		3 (Safety-related operating mode inputs: I1, I2, I3)
		2 (Safety-related monitoring inputs: MI1, MI2)
Discrepancy time	2 s (I1, I2, I3)
Discrepancy time		2.5 s (MI1, MI2)
Input voltage range "0" signal	0 V DC ... 5 V DC
Input voltage range "1" signal	15 V DC ... 30 V DC
Input current range "0" signal	0 mA ... 1.5 mA
Inrush current	< 5 mA
Filter time	max. 2 ms (Test pulse width; low test pulses for operating mode and monitoring inputs)
Filter time		Test pulse rate = 5 x Test pulse width
Max. permissible overall conductor resistance	150 Ω
Protective circuit	33 V suppressor diode
Current consumption	typ. 4 mA (at U_S)
Measurement
Input name	Proximity switch inputs
Description of the input	NPN, IEC 61131-2, type 1
Number of inputs	2 (Safety-related proximity switch inputs: IN1 IN2)
Input voltage range "0" signal	0 V DC ... 5 V DC
Input voltage range "1" signal	15 V DC ... 30 V DC
Input current range "0" signal	0 mA ... 1.5 mA
Inrush current	< 12 mA
Precision	± 2 % (in reference to the parameterized limit value)
Limit frequency	max. 2 kHz (Minimum pulse duration: 45 µs)
Max. permissible overall conductor resistance	150 Ω
Protective circuit	33 V suppressor diode
Current consumption	typ. 10 mA (at U_S)
Measurement
Input name	Encoder input
Description of the input	TTL, HTL, Sin/Cos
Number of inputs	1 (Safety-related encoder input, RJ45)
Precision	± 2 % (in reference to the parameterized limit value)
Limit frequency	max. 400 kHz
Limit frequency		max. 250 kHz For active diagnostic safety encoder
Max. permissible overall conductor resistance	150 Ω
HTL Signal form/signal level	0 V DC ... 3 V DC (Low)
HTL Signal form/signal level		12 V DC ... 30 V DC (High)
TTL Signal form/signal level	0 V DC ... 0.9 V DC (Low)
TTL Signal form/signal level		2.5 V DC ... 5 V DC (High)
Sine / cosine Signal form/signal level	2 V DC ... 3 V DC (1 V_pp differential signal)
Current consumption	< 3 mA (Per track for U_S)

Relay: Enabling current path
Output description	2 NO contacts each in series, without delay, floating
Number of outputs	2 (safety-related N/O contacts: 13/14, 23/24)
Contact type	2 enabling current paths
Contact material	AgSnO₂
Switching voltage	min. 12 V AC/DC
Switching voltage		max. 250 V AC/DC (Observe the load curve)
Switching capacity	min. 60 mW
Inrush current	min. 3 mA
Inrush current		max. 6 A
Switching capacity in accordance with IEC 60947-5-1	4 A (24 V (DC13))
Switching capacity in accordance with IEC 60947-5-1		5 A (250 V (AC15))
Limiting continuous current	6 A
Sq. Total current	72 A² (observe derating)
Switching frequency	max. 0.5 Hz
Mechanical service life	10x 10⁶ cycles
Output fuse	6 A gL/gG
Signal
Output description	PNP
Number of outputs	2 (Non-safety-related signal outputs: MO1, MO2)
Voltage	approx. 22 V DC (U_s - 2 V)
Current	max. 100 mA
Maximum inrush current	500 mA (Δt = 1 ms at U_s)
Protective circuit	33 V suppressor diode
Short-circuit protection	no

Connection technology
pluggable	yes
Conductor connection
Connection method	Push-in connection
Conductor cross section rigid	0.2 mm² ... 1.5 mm²
Conductor cross section flexible	0.2 mm² ... 1.5 mm²
Conductor cross section, flexible, with ferrule, with plastic sleeve	0.25 mm² ... 1.5 mm² (only together with CRIMPFOX 6)
Conductor cross section flexible, with ferrule without plastic sleeve	0.25 mm² ... 1.5 mm² (only together with CRIMPFOX 6)
Conductor cross-section AWG	24 ... 16
Stripping length	8 mm

Status display	2x LED green (OUT1, OUT2)
Operating voltage display	1 x green LED (PWR)

Width	22.5 mm
Height	117.5 mm
Depth	114.5 mm

Housing material

Polyamide

Safety data
Stop category	0
Safety data: EN ISO 13849
Category	4
Performance level (PL)	e (6 A DC1, 17520 switching cycles/year)
Safety data: IEC 61508 - High demand
Equipment type	Type B
Safety Integrity Level (SIL)	3
Probability of a hazardous failure per hour (PFH_D)	2.74 x 10^-8 (6 A DC1, 17520 switching cycles/year)
Proof test interval	240 Months
Duration of use	240 Months

Ambient conditions
Degree of protection	IP20
Min. degree of protection of inst. location	IP54
Ambient temperature (operation)	-40 °C ... 55 °C (observe derating)
Ambient temperature (storage/transport)	-40 °C ... 70 °C
Maximum altitude	≤ 2000 m (Above sea level)
Max. permissible humidity (storage/transport)	75 % (on average, 85% infrequently, non-condensing)
Max. permissible relative humidity (operation)	75 % (on average, 85% infrequently, non-condensing)
Shock	15g
Vibration (operation)	10 Hz ... 150 Hz, 2g