PSR-MC31-2SDO-1DO-24DC-SP - Safety device Phoenix Contact

Mã sản phẩm: 1015503

Danh mục: PHOENIX CONTACT, Switch, Measure and Monitor Phoenix Contact,

Safety relay module for safety shut-off mats, switching strips, emergency stop, safety doors, and light grids up to SIL 3, Cat. 4, PL e, 1 or 2-channel operation, automatic or manual start, 2 safe HL outputs, 1 signal output, US = 24 V DC, pluggable Push-in terminal block

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

Product type	Safety relays
Product family	PSRmini
Application	Emergency stop
		Safety door
		Safety shut-off mats
		Light grid
Times
Typical response time	< 200 ms (automatic start)
Typical response time		< 175 ms (manual, monitored start)
Typ. starting time with U_s	< 200 ms (with U_s when controlled via A1)
Response time	< 10 ms (Take the extension of the response time into consideration if you switch several devices in sequence.)
Restart time	< 250 ms (Boot time)
Recovery time	250 ms (following demand of the safety function)

Maximum power dissipation for nominal condition	3.1 W (U_B = 30 V , I_L1 = I_L2 = 2.4 A)
Nominal operating mode	100% operating factor
Air clearances and creepage distances between the power circuits
Rated insulation voltage	50 V
Rated insulation voltage		50 V AC
Rated surge voltage/insulation	Basic insulation 4 kV between all current paths and housing
Supply
Designation	A1/A2
Rated control circuit supply voltage U_S	19.2 V DC ... 30 V DC
Rated control circuit supply voltage U_S	24 V DC -20 % / +25 % (provide external protection)
Rated control supply current I_S	typ. 54 mA (No load)
Power consumption at U_S	typ. 1.3 W
Inrush current	< 5 A (Δt = 200 µs at U_s)
Filter time	1 ms (For the logic. At A1 in the event of voltage dips at U_s)
Protective circuit	Parallel protection against polarity reversal; Suppressor diode (Provide external protection, see safety notes. Fuse type: 5 A FF)

Digital: Sensor circuit (S10, S12, S22)
Description of the input	safety-related sensor inputs
Description of the input		IEC 61131-2 type 3 (S10, S12) PNP (S22)
Number of inputs	3
Input voltage range "0" signal	0 V DC ... 5 V DC (S10, S12)
Input voltage range "0" signal		S22 open
Input voltage range "1" signal	11 V DC ... 30 V DC (S10, S12)
Input voltage range "1" signal		0 V ... 0 V (S22)
Input current range "0" signal	0 mA ... 2 mA (S10, S12)
Inrush current	< 10 mA (Typically with U_S at S10/S12, Δt = 500 µs)
Inrush current		> -5 mA (typ. with U_S at S22, Δt = 500 µs)
Filter time	max. 1.5 ms (Test pulse width of low test pulses)
		Test pulse rate = 5 x Test pulse width
		Does not apply for S22
		Deactivate the switch-on pulses for safety applications.
Concurrence	∞
Max. permissible overall conductor resistance	150 Ω
Protective circuit	Suppressor diode
Current consumption	4 mA (S10, S12)
Current consumption		-4 mA (S22)
Digital: Start circuit (S34, S35)
Description of the input	non-safety-related
Number of inputs	2
Input voltage range "1" signal	19.2 V DC ... 30 V DC
Inrush current	< 10 mA (Typically with U_S, Δt < 100 ms)
Max. permissible overall conductor resistance	150 Ω
Protective circuit	Suppressor diode
Current consumption	< 7 mA (Typically with U_S at S34)
Current consumption		< 5 mA (Typically with U_S at S35)
Digital: External release (S36)
Description of the input	safety-related
Description of the input		IEC 61131-2 type 3
Number of inputs	1
Input voltage range "0" signal	0 V DC ... 5 V DC
Input voltage range "1" signal	11 V DC ... 30 V DC
Input current range "0" signal	0 mA ... 2 mA
Inrush current	< 10 mA (Δt = 500 µs)
Filter time	max. 1.5 ms (Test pulse width of low test pulses)
Filter time		Test pulse rate = 5 x Test pulse width
Max. permissible overall conductor resistance	150 Ω
Protective circuit	Suppressor diode
Current consumption	7 mA

Digital: 14, 24
Output description	Safety-related digital outputs
Output description		PNP, IEC 61131-2 Type 2
Number of outputs	2
Protective circuit	Freewheeling circuit for inductive loads
Output voltage	≥ 23 V DC (U_s - 1 V)
Leakage current	max. 1 mA (in the safe state)
Ohmic load	min. 12 Ω
Max. capacitive load	max. 10 µF (2.4 A load)
Max. capacitive load		max. 4.7 µF (1 A load)
Max. inductive load	max. 1 H
Limitation of the voltage induced on circuit interruption	max. 50 V
Output current	max. 2.4 A
Inrush current	max. 4.8 A (Δt = 10 ms)
Min. load current	2 mA
Switching frequency	1 Hz (Resistive, inductive, capacitive)
Output voltage when switched off	< 5 V DC (in the safe state)
Test pulses	< 1 ms (Test pulse width of low test pulses)
Signal: M1
Output description	PNP
Output description		non-safety-related
Number of outputs	1
Voltage	approx. 22 V DC (U_s - 2 V)
Current	max. 100 mA
Maximum inrush current	500 mA (Δt = 1 ms at U_s)
Protective circuit	Suppressor diode
Short-circuit protection	Yes

Connection technology
pluggable	yes
Conductor connection
Connection method	Push-in connection
Conductor cross section rigid	0.2 mm² ... 1.5 mm²
Conductor cross section flexible	0.2 mm² ... 1.5 mm²
Conductor cross section, flexible, with ferrule, with plastic sleeve	0.25 mm² ... 1.5 mm² (only together with CRIMPFOX 6)
Conductor cross section flexible, with ferrule without plastic sleeve	0.25 mm² ... 1.5 mm² (only together with CRIMPFOX 6)
Conductor cross-section AWG	24 ... 16
Stripping length	8 mm

Status display	3 x green LED
Operating voltage display	1 x green LED
Error indication	1 x red LED

Width	12.5 mm
Height	116.6 mm
Depth	114.5 mm

Housing material

Polyamide

Safety data
Stop category	0
Safety data: EN ISO 13849
Category	4
Performance level (PL)	e
Safety data: IEC 61508 - High demand
Equipment type	Type A
Safety Integrity Level (SIL)	3
Probability of a hazardous failure per hour (PFH_D)	1.00 x 10^-9
Proof test interval	240 Months
Duration of use	240 Months

Ambient conditions
Degree of protection	IP20
Min. degree of protection of inst. location	IP54
Ambient temperature (operation)	-40 °C ... 70 °C (observe derating)
Ambient temperature (storage/transport)	-40 °C ... 70 °C
Maximum altitude	≤ 2000 m (Above sea level)
Max. permissible humidity (storage/transport)	75 % (on average, 85% infrequently, non-condensing)
Max. permissible relative humidity (operation)	75 % (on average, 85% infrequently, non-condensing)
Shock	30g
Vibration (operation)	10 Hz ... 150 Hz, 5g