PSR-M-EF7-XC-SAI4-PI - Extension module Phoenix Contact

Mã sản phẩm: 1337851

Danh mục: PHOENIX CONTACT, Switch, Measure and Monitor Phoenix Contact,

Safe extension module with 4 safe analog inputs, 0 V ... 10 V; 0 mA or 4 mA ... 20 mA; TBUS interface, up to Cat. 4/PL e, SIL 3, plug-in Push-in terminal block, TBUS connector included

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

Product type	Safety device
Application	Analog IN
Insulation characteristics
Protection class	III
Times
Response time	see user manual
Restart time	min. 5 s (Boot time)
Restart time		max. 10 s (Boot time)

Maximum power dissipation for nominal condition	2.76 W (with max. permissible load)
Nominal operating mode	100% operating factor
Interfaces	DIN rail TBUS for connection to the master module, supplied as standard
Air clearances and creepage distances
Rated insulation voltage	250 V AC
Rated surge voltage/insulation	Basic insulation 4 kV between all current paths and housing
Rated surge voltage/insulation		Electrical isolation, 0.5 kV functional insulation between logic and analog inputs and between the analog inputs
Supply
Designation	A1/A2
Rated control circuit supply voltage U_S	19.2 V DC ... 28.8 V DC
Rated control circuit supply voltage U_S	24 V DC -20 % / +20 % (external fuse, typically 6 A)
Rated control supply current I_S	typ. 82 mA (without sensor supply)
Rated control supply current I_S		typ. 212 mA (with sensor supply)
Power consumption at U_S	typ. 1.96 W (without sensor supply)
Power consumption at U_S		typ. 5.08 W (with sensor supply)
Inrush current	max. 14 A (Δt = 1 ms at U_s)
Filter time	typ. 5 ms (in the event of voltage dips at U_s)
Protective circuit	Serial protection against polarity reversal

General
Protective circuit	Overload protection of the current inputs; Suppressor diode
Analog
Input name	IN S1, IN S2, IN S3, IN S4
Description of the input	Safety-oriented analog inputs, configurable as current or voltage inputs, galvanically isolated
Number of inputs	4
Connection technology	2-conductor, 3-conductor or 4-conductor (2-conductor sensor signal + 2-conductor sensor supply)
Note regarding the connection technology	shielded
Scanning rate	2.5/5/10/16.6/20/50/60/100/200/400/800/1000/2000/4000 Hz
Current input signal	0 mA ... 25 mA (Measuring range)
		0 mA ... 20 mA (Configurable measuring range with diagnostics range 20.1 mA ... 23 mA)
		4 mA ... 20 mA (Configurable measuring range with diagnostics range 20.1 mA ... 23 mA (upper limit), 2.5 mA ... 3.8 mA (lower limit))
Voltage input signal	0 V ... 12 V (Measuring range)
Voltage input signal		0 V ... 10 V (Configurable measuring range with diagnostics range 10.05 V ... 11.5 V (upper limit), 0.1 V (lower limit))
Max. permissible current	max. 35 mA (as current input)
Permissible voltage	max. 24 V (as current input)
Permissible voltage		max. 14 V (as voltage input)
Input resistance current input	290 Ω ±25 % (incl. internal protective circuit)
Input resistance of voltage input	185 kΩ ±25 %
A/D converter resolution	16 bit
Resolution (current)	381 nA
Resolution (voltage)	152 µV
Precision	typ. ± 2 % (as current input, relative to the measuring range final value)
		max. ± 2.5 % (as current input)
		typ. ± 1 % (as voltage input, relative to the measuring range final value)
		max. ± 1.5 % (as voltage input)
Temperature coefficients	typ. ± 0.07 %/K
Temperature coefficients		max. ± 0.07 %/K
Limit frequency (3 dB)	160 Hz (RC low pass, 1st order, as current input)
Limit frequency (3 dB)		4 Hz (RC low pass, as voltage input)
Frequency	20 Hz (max. recommended sensor signal frequency, as current input)
Frequency		2 Hz (max. recommended sensor signal frequency, as voltage input)
Permissible cable length	max. 100 m (per input)
Protective circuit	Overload protection of the current inputs
Protective circuit		Overload protection of the voltage inputs

Sensor supply: OUT S1/0V ...OUT S4/0V
Description	Sensor supply voltage per analog input
Supply voltage	24 V DC ±3 %
Current	max. 30 mA (Sensor current recording per channel)
Short-circuit-proof	yes
Protective circuit	Overload protection Overload detection at  38 mA

Connection technology
pluggable	yes
Conductor connection
Connection method	Push-in connection
Conductor cross section rigid	0.2 mm² ... 2.5 mm²
Conductor cross section flexible	0.2 mm² ... 2.5 mm²
Conductor cross-section AWG	24 ... 16
Stripping length	10 mm

Status display	4x LED (yellow, red)
Operating voltage display	1 x green LED

Width	22.61 mm
Height	107.74 mm
Depth	113.6 mm

Housing material

Polyamide PA non-reinforced

Safety data
Stop category	0
Safety data: EN ISO 13849
Performance level (PL)	e (2-channel wiring)
Performance level (PL)		d (1-channel wiring)
Safety data: IEC 61508 - High-demand for 2-channel wiring
Equipment type	Type B
Safety Integrity Level (SIL)	3
Probability of a hazardous failure per hour (PFH_D)	2.69 x 10^-8
Proof test interval	240 Months
Duration of use	240 Months
Integrity requirement	IEC 61508 - High-demand for 1-channel wiring
Equipment type	Type B
Safety Integrity Level (SIL)	2
Probability of a hazardous failure per hour (PFH_D)	2.69 x 10^-8
Proof test interval	240 Months
Duration of use	240 Months
Equipment type	Type B
Safety Integrity Level (SIL)	2
Probability of a hazardous failure on demand (PFD_AVG)	1.15 x 10^-3
Proof test interval	240 Months
Duration of use	240 Months

Ambient conditions
Degree of protection	IP20
Min. degree of protection of inst. location	IP54
Ambient temperature (operation)	-10 °C ... 70 °C (observe derating)
Ambient temperature (storage/transport)	-20 °C ... 85 °C
Maximum altitude	≤ 2000 m (Above sea level)
Max. permissible humidity (storage/transport)	95 % (non-condensing)
Max. permissible relative humidity (operation)	95 % (non-condensing)
Shock	10g for Δt = 16 ms (continuous shock, 1000 shocks in each space direction)
Vibration (operation)	10 Hz ... 150 Hz, 2g