PSR-M-B2-XC-SDI8-SDO4-DO4-PI - Safety module Phoenix Contact

Mã sản phẩm: 1337849

Danh mục: PHOENIX CONTACT, Switch, Measure and Monitor Phoenix Contact,

Configurable safety module (basic module), 8 safe inputs, 4 safe outputs, 4 reset inputs or 4 signal outputs, 4 clock outputs, can be extended via TBUS, up to SIL 3, Cat. 4/PL e, plug-in Push-in terminal block, TBUS connector not included

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

Product type	Safety device
Application	Emergency stop
		Light grid
		Safety door
		Safe shutdown
Times
Response time	see user manual
Restart time	min. 5 s (Boot time)
Restart time		max. 10 s (Boot time)

Maximum power dissipation for nominal condition	7.48 W (with max. permissible load)
Nominal operating mode	100% operating factor
Interfaces	DIN rail TBUS for connection to the master module, not supplied as standard
Air clearances and creepage distances between the power circuits
Rated insulation voltage	250 V AC
Rated surge voltage/insulation	See section “Insulation coordination”
Supply
Designation	A1/A2
Rated control circuit supply voltage U_S	19.2 V DC ... 28.8 V DC
Rated control circuit supply voltage U_S	24 V DC -20 % / +20 % (external fuse, typically 4 A)
Rated control supply current I_S	typ. 55 mA (Outputs inactive)
Power consumption at U_S	typ. 1.32 W (Outputs inactive)
Inrush current	9.16 A (Δt = 0.5 ms at U_s)
Filter time	typ. 5 ms (in the event of voltage dips at U_s)
Protective circuit	Serial protection against polarity reversal

Digital: IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8
Description of the input	Safety-related digital inputs
Description of the input		NPN
Number of inputs	8
Input voltage range "0" signal	0 V DC ... 5 V DC (for safe Off)
Input voltage range "1" signal	11 V DC ... 28.8 V DC
Input current range "0" signal	< 0.2 mA
Inrush current	max. 524 mA (Δt = 6 µs at U_s)
Filter time	min. 3 ms (adjustable)
		max. 250 ms (adjustable)
		Test pulse rate ≥ 2x set filter time, min. Test pulse rate = 10 ms
		max. 3 ms (Test pulse rate ≥ 10x configured filter time for low test pulse)
		max. 250 ms (Test pulse rate ≥ 10x configured filter time for high test pulse)
Cable length	max. 100 m
Max. permissible overall conductor resistance	max. 1.2 kΩ (Input and reset circuit at U_S)
Current consumption	typ. 3.7 mA (typically with U_S)
Current consumption		max. 4.6 mA (at a control voltage of 28.8 V DC)
Digital: Reset inputs (FBK)
Description of the input	configurable (as signal output or reset input)
Description of the input		NPN, digital
Number of inputs	4 (Non-safe inputs)
Input voltage range "0" signal	0 V DC ... 5 V DC (for safe Off)
Input voltage range "1" signal	11 V DC ... 28.8 V DC
Input current range "0" signal	< 0.2 mA
Inrush current	max. 906.53 mA (Δt = 10 µs at U_s)
Filter time	250 ms (constant)
		< 250 ms (Test pulse duration)
		> 1 s (Test pulse rate)
Cable length	max. 100 m
Max. permissible overall conductor resistance	1.2 kΩ (Input and reset circuit at U_S)
Current consumption	typ. 5.7 mA (typically with U_S)
Current consumption		max. 7 mA (at a control voltage of 28.8 V DC)

Digital: O1, O2, O3, O4
Output description	Safety-related digital outputs
		PNP, OSSD, digital
		IEC 61131-2 type 0.25 (observe limiting continuous current)
Number of outputs	4
Short-circuit protection	no
Output voltage	< 0.3 V (Low state)
Leakage current	< 500 µA (Low state)
Cable length	max. 100 m
Max. capacitive load	max. 820 nF
Max. inductive load	See "Protective circuit"
Limiting continuous current	400 mA (per channel)
Limiting continuous current		1.6 A (Total current of all safe digital outputs)
Inrush current	max. 600 mA (Δt = 25 ms at U_s)
Nominal output voltage	24 V DC (Supply via A1)
Nominal output voltage range	18.6 V DC ... 28.2 V DC (U_S - 0,7 V)
Switching frequency	max. 1/4 x t_Cycle [Hz]
Test pulses	< 235 µs (Test pulse width of low test pulses)
		≥ 650 ms (Test pulse rate for low test pulse)
		< 150 µs (Test pulse width, high test pulse)
		≥ 1.5 s (Test pulse rate, high test pulse)
Discharging circuit	Yes, internal
Signal: MO1, MO2, MO3, MO4
Output description	PNP, digital, IEC 61131-2 type 0.1
Output description		non-safety-related, configurable (as signal output or reset input)
Number of outputs	4
Output voltage when switched off	max. 0.1 V
Voltage	24 V DC (via A1)
Maximum inrush current	1.1 A (Δt = 3 s at U_s)
Limiting continuous current	100 mA (per channel)
Limiting continuous current		400 mA (Total current of all digital signal outputs)
Leakage current	max. 4.5 mA (Low state)
Switching frequency	max. 1/4 x t_Cycle [Hz]
Short-circuit protection	Yes (self-limitation at 1.1 A)
Cable length	max. 100 m
Clock: T1, T2, T3, T4
Output description	PNP, digital, IEC 61131-2 type 0.1
Number of outputs	4
Voltage	24 V DC (via A1)
Maximum inrush current	1.1 A (Δt = 3 s at U_s)
Limiting continuous current	100 mA (per channel)
Limiting continuous current		400 mA (Total current of all outputs)
Test pulses	≤ 200 µs (Test pulse duration)
Test pulses		Test pulse rate = 8 x t_Cycle [ms]
Short-circuit protection	Yes (self-limitation at 1.1 A)
Cable length	max. 100 m
Max. capacitive load	max. 470 nF
Max. inductive load	max. 2.4 mH
Discharging circuit	Yes, internal

Connection technology
pluggable	yes
Conductor connection
Connection method	Push-in connection
Conductor cross section rigid	0.2 mm² ... 2.5 mm²
Conductor cross section flexible	0.2 mm² ... 2.5 mm²
Conductor cross-section AWG	24 ... 16
Stripping length	10 mm

Data: Service interface
Connection method	USB 2.0 Hi-Speed
Number of connections	1
Data: Local bus
Note	via the PSR-TBUS DIN rail connector

Status display	1 x LED (green), 1 x LED (orange), 1 x LED (blue)
		4 x LED (green, yellow, red)
		12 x LED (yellow)
Operating voltage display	1 x green LED
Error indication	2 x LED (red)

Width	22.61 mm
Height	107.74 mm
Depth	113.6 mm

Housing material

Polyamide PA non-reinforced

Safety data: EN ISO 13849
Performance level (PL)	e (2-channel wiring)
Performance level (PL)		d (1-channel wiring)
Safety data: IEC 61508 - High-demand for 2-channel wiring
Equipment type	Type B
Safety Integrity Level (SIL)	3
Probability of a hazardous failure per hour (PFH_D)	2.51 x 10^-8
Proof test interval	240 Months
Duration of use	240 Months
Integrity requirement	IEC 61508 - High-demand for 1-channel wiring
Equipment type	Type B
Safety Integrity Level (SIL)	2
Probability of a hazardous failure per hour (PFH_D)	2.51 x 10^-8
Proof test interval	240 Months
Duration of use	240 Months
Equipment type	Type B
Safety Integrity Level (SIL)	2
Probability of a hazardous failure on demand (PFD_AVG)	5.30 x 10^-4
Proof test interval	240 Months
Duration of use	240 Months

Ambient conditions
Degree of protection	IP20
Min. degree of protection of inst. location	IP54
Ambient temperature (operation)	-10 °C ... 70 °C (observe derating)
Ambient temperature (storage/transport)	-20 °C ... 85 °C
Maximum altitude	≤ 2000 m (Above sea level)
Max. permissible humidity (storage/transport)	95 % (non-condensing)
Max. permissible relative humidity (operation)	95 % (non-condensing)
Shock	10g for Δt = 16 ms (continuous shock, 1000 shocks in each space direction)
Vibration (operation)	10 Hz ... 150 Hz, 2g