PSR-M-B1-SDI8-SDO2-DO2-PI - Safety module Phoenix Contact

Mã sản phẩm: 1104972

Danh mục: PHOENIX CONTACT, Switch, Measure and Monitor Phoenix Contact,

Configurable safety module (basic module), 8 safe inputs, 2 safe outputs, 2 reset inputs, 2 signal outputs, 4 clock outputs, can be extended via TBUS, up to SIL 3, Cat. 4/PL e, plug-in Push-in terminal block, TBUS connector not included

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

Product type	Safety device
Application	Emergency stop
		Light grid
		Safety door
		Safe shutdown
Insulation characteristics
Protection class	III (EN 50178)
Times
Response time	see user manual
Restart time	min. 5 s (Boot time)
Restart time		max. 10 s (Boot time)

Maximum power dissipation for nominal condition	6.24 W (with max. permissible load)
Nominal operating mode	100% operating factor
Interfaces	DIN rail TBUS for connection to the master module, not supplied as standard
Air clearances and creepage distances between the power circuits
Rated insulation voltage	250 V AC
Rated surge voltage/insulation	Basic insulation 4 kV between all current paths and housing
Supply
Designation	A1/A2
Rated control circuit supply voltage U_S	19.2 V DC ... 28.8 V DC
Rated control circuit supply voltage U_S	24 V DC -20 % / +20 % (external fuse, typically 4 A)
Rated control supply current I_S	typ. 55 mA (Outputs inactive)
Rated control supply current I_S		typ. 70 mA (Outputs active, without load)
Power consumption at U_S	typ. 1.32 W (Outputs inactive)
Inrush current	9.5 A (Δt = 1 ms at U_s)
Filter time	typ. 5 ms (at A1 in the event of voltage dips at U_s)
Protective circuit	Inverse-parallel protection against polarity reversal
Protective circuit		Suppressor diode

Digital: IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8
Description of the input	Safety-related digital inputs
Description of the input		EN 61131-2 type 1
Number of inputs	8
Input voltage range "0" signal	0 V DC ... 5 V DC
Input voltage range "1" signal	15 V DC ... 28.8 V DC
Input current range "0" signal	< 1 mA
Filter time	min. 3 ms ±2 ms (adjustable)
		max. 250 ms ±2 ms (adjustable)
		Test pulse rate ≥ 2x set filter time, min. Test pulse rate = 10 ms
Cable length	max. 100 m (per input)
Max. permissible overall conductor resistance	max. 1.2 kΩ (Input and reset circuit at U_S)
Protective circuit	Suppressor diode
Current consumption	typ. 8 mA (typically with U_S)
Current consumption		max. 10 mA (at a control voltage of 28.8 V DC)
Digital: Reset inputs (FBK1, FBK2)
Description of the input	IEC 61131-2 type 3
Description of the input		non-safety-related (configurable)
Number of inputs	2
Input voltage range "0" signal	0 V DC ... 5 V DC
Input voltage range "1" signal	11 V DC ... 28.8 V DC
Input current range "0" signal	< 1 mA
Filter time	250 ms ±2 ms (Test pulse rate > 500 ms)
Cable length	max. 100 m (per input)
Max. permissible overall conductor resistance	1.2 kΩ (Input and reset circuit at U_S)
Protective circuit	Suppressor diode
Current consumption	typ. 10 mA (typically with U_S)
Current consumption		max. 13 mA (at a control voltage of 28.8 V DC)
Digital: Enable inputs (EN1, EN2)
Number of inputs	2
Input voltage range "0" signal	0 V DC ... 5 V DC
Input voltage range "1" signal	8 V DC ... 28.8 V DC
Input current range "0" signal	< 0.2 mA
Filter time	100 ms ±2 ms (Test pulse duration)
Filter time		> 1 s (Test pulse rate)
Cable length	max. 100 m (per input)
Max. permissible overall conductor resistance	max. 12 kΩ
Protective circuit	Suppressor diode
Current consumption	typ. 0.7 mA (typically with U_S)
Current consumption		max. 1 mA (at a control voltage of 28.8 V DC)

Digital: O1A, O1B, O2A, O2B
Output description	Safety-related digital outputs
		PNP, OSSD
		IEC 61131-2 type 0.5 (observe limiting continuous current)
Number of outputs	4 (can be used as 2 two-channel outputs)
Protective circuit	Suppressor diode
Short-circuit protection	Yes (self-limitation at 1.1 A)
Leakage current	max. 500 µA
Cable length	max. 100 m (per output)
Ohmic load	min. 50 Ω (Observe limiting continuous current)
Max. capacitive load	max. 680 nF
Max. inductive load	max. 1.4 mH
Limiting continuous current	400 mA (per channel)
Limiting continuous current		1.6 A (Total current of all safe digital outputs)
Inrush current	max. 750 mA (Δt  1 s)
Nominal output voltage	24 V DC (Supply via A1)
Nominal output voltage range	18 V DC ... 27.6 V DC (U_S - 1.2 V)
Switching frequency	max. 1/4 x t_Cycle [Hz]
Output voltage when switched off	< 1.5 V
Test pulses	< 80 µs (Test pulse width of low test pulses)
		Test pulse rate for low test pulses > 2 x T_Cycle
		< 20 µs (Test pulse width, high test pulse)
		≥ 1.5 s (Test pulse rate, high test pulse)
Discharging circuit	Yes, internal
Signal: MO1, MO2
Output description	PNP, IEC 61131-2 Typ 0,1
Output description		non-safety-related
Number of outputs	2
Output voltage when switched off	max. 0.1 V
Voltage	24 V DC (via A1)
Maximum inrush current	1.1 A (Δt = 3 s at U_s)
Limiting continuous current	100 mA (per channel)
Limiting continuous current		200 mA (Total current of all digital signal outputs)
Leakage current	max. 100 µA
Switching frequency	max. 1/4 x t_Cycle [Hz]
Protective circuit	Suppressor diode
Short-circuit protection	Yes (self-limitation at 1.1 A)
Cable length	max. 100 m (per output)
Clock: T1, T2, T3, T4
Output description	PNP, IEC 61131-2 type 0.5
Number of outputs	4
Voltage	24 V DC (via A1)
Output voltage when switched off	max. 0.1 V
Maximum inrush current	1.1 A (Δt = 3 s at U_s)
Limiting continuous current	100 mA (per channel)
Limiting continuous current		400 mA (Total current of all outputs)
Leakage current	max. 100 µA
Test pulses	≤ 220 µs (Test pulse duration)
Test pulses		Test pulse rate = 8 x t_Cycle [ms]
Short-circuit protection	Yes (self-limitation at 1.1 A)
Cable length	max. 100 m (per output)
Max. capacitive load	max. 470 nF
Max. inductive load	max. 2.4 mH
Discharging circuit	Yes, internal

Connection technology
pluggable	yes
Conductor connection
Connection method	Push-in connection
Conductor cross section rigid	0.2 mm² ... 2.5 mm²
Conductor cross section flexible	0.2 mm² ... 2.5 mm²
Conductor cross-section AWG	24 ... 16
Stripping length	10 mm

Status display	1 x LED (green), 1 x LED (orange), 1 x LED (blue)
		2 x LED (green, red)
		12 x LED (yellow)
Operating voltage display	1 x green LED
Error indication	2 x LED (red)

Width	22.61 mm
Height	107.74 mm
Depth	113.6 mm

Housing material

Polyamide PA non-reinforced

Safety data
Stop category	0
Safety data: EN ISO 13849
Performance level (PL)	e (2-channel wiring)
Performance level (PL)		d (1-channel wiring)
Safety data: IEC 61508 - High-demand for 2-channel wiring
Equipment type	Type B
Safety Integrity Level (SIL)	3
Probability of a hazardous failure per hour (PFH_D)	6.86 x 10^-9
Proof test interval	240 Months
Duration of use	240 Months
Integrity requirement	IEC 61508 - High-demand for 1-channel wiring
Equipment type	Type B
Safety Integrity Level (SIL)	2
Probability of a hazardous failure per hour (PFH_D)	6.86 x 10^-9
Proof test interval	240 Months
Duration of use	240 Months

Ambient conditions
Degree of protection	IP20
Min. degree of protection of inst. location	IP54
Ambient temperature (operation)	-10 °C ... 55 °C (observe derating)
Ambient temperature (storage/transport)	-20 °C ... 85 °C
Maximum altitude	≤ 2000 m (Above sea level)
Max. permissible humidity (storage/transport)	95 % (non-condensing)
Max. permissible relative humidity (operation)	95 % (non-condensing)
Shock	10g for Δt = 16 ms (continuous shock, 1000 shocks in each space direction)
Vibration (operation)	10 Hz ... 150 Hz, 2g