PLC-RSC-24DC/21HC/EX - Relay Module Phoenix Contact

Mã sản phẩm: 2909519

Danh mục: PHOENIX CONTACT, Switch, Measure and Monitor Phoenix Contact,

PLC-INTERFACE, consisting of DIN-rail-mountable basic terminal block in 14 mm with screw connection and plug-in relay with 10 A power contact, 1 changeover contact, 24 V DC input voltage. Approved according to ATEX/IECEx (Zone 2) and Ex Zone Class I, Div. 2.

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

Utilization restriction
EMC note	EMC: class A product, see manufacturer's declaration in the download area

Product type	Relay Module
Product family	PLC-INTERFACE
Application	High continuous currents
Application		potentially explosive areas
Operating mode	100% operating factor
Mechanical service life	3x 10⁷ cycles
Insulation characteristics
Insulation	Safe isolation, reinforced insulation
Insulation characteristics: Standards/regulations
Insulation	Safe isolation, reinforced insulation
Overvoltage category	III
Pollution degree	3

Maximum power dissipation for nominal condition	0.43 W
Test voltage (Winding/contact)	4 kV AC (50 Hz, 1 min., winding/contact)
Standards/regulations
Rated insulation voltage	250 V AC
Rated surge voltage	6 kV

Coil side
Nominal input voltage U_N	24 V DC
Input voltage range	20.2 V DC ... 33.6 V DC (20 °C)
Typical input current at U_N	18 mA
Typical response time	8 ms
Typical release time	10 ms
Protective circuit	Reverse polarity protection; Polarity protection diode
Protective circuit		Freewheeling diode; Freewheeling diode
Operating voltage display	Yellow LED

Switching
Contact type	1 changeover contact
Type of switch contact	Single contact
Drive and function	monostable
Drive (polarity)	polarized
Contact material	AgNi
Maximum switching voltage	250 V AC/DC (The separating plate PLC-ATP should be installed for voltages larger than 250 V (L1, L2, L3) between identical terminal blocks in adjacent modules. Potential bridging is then carried out with FBST 8-PLC... or ...FBST 500...)
Minimum switching voltage	12 V (10 mA)
Limiting continuous current	10 A
Limiting continuous current		6 A (value applies to connections 12. If connections 12 are bridged, the normal value applies.)
Maximum inrush current	30 A (300 ms)
Min. switching current	10 mA (12 V)
Interrupting rating (ohmic load) max.	240 W (at 24 V DC)
		58 W (at 48 V DC)
		48 W (at 60 V DC)
		50 W (at 110 V DC)
		80 W (at 220 V DC)
		2500 VA (for 250 V AC)
Interrupting rating (ohmic load) max. bridged	144 W (for 24 V DC. Value applies to connections 12. If connections 12 are bridged, the normal value applies.)
Interrupting rating (ohmic load) max. bridged		1500 VA (for 250 V AC. Value applies to connections 12. If connections 12 are bridged, the normal value applies.)
Switching capacity	2 A (at 24 V, DC13)
		0.2 A (at 110 V, DC13)
		0.2 A (at 250 V, DC13)
		6 A (at 24 V, AC15)
		6 A (at 120 V, AC15)
		6 A (at 250 V, AC15)

Connection method	Screw connection
Stripping length	8 mm
Screw thread	M3
Conductor cross section rigid	0.14 mm² ... 2.5 mm²
Conductor cross section flexible	0.14 mm² ... 2.5 mm²
		0.2 mm² ... 2.5 mm² (Single ferrule)
		2x 0.5 mm² ... 1.5 mm² (TWIN ferrule)
Conductor cross section AWG	26 ... 14
Tightening torque	0.6 Nm ... 0.8 Nm

Width	14 mm
Height	80 mm
Depth	94 mm

Flammability rating according to UL 94

V0 (Housing)

Ambient conditions
Degree of protection (Relay)	RT III (Relay)
Degree of protection (Relay base)	IP20 (Relay base)
Ambient temperature (operation)	-40 °C ... 70 °C (UL)
Ambient temperature (operation)		-40 °C ... 70 °C (ATEX / IECEx)
Ambient temperature (storage/transport)	-40 °C ... 85 °C

CE
Certificate	CE-compliant
ATEX
Identification	 II 3G Ex ec nC IIC T4 Gc
Certificate	IBExU16ATEXB015 X
IECEx
Identification	Ex ec nC IIC T4 Gc
Certificate	IECEx IBE 16.0029X
UKCA Ex (UKEX)
Identification	 II 3 G Ex ec nC IIC T4 Gc
Certificate	PxCIF21UKEX2909514X
UL, USA
Identification	Class I, Zone 2, AEx nA nC IIC T6
UL, USA/Canada
Identification	Class I, Div. 2, Groups A, B, C, D
UL, Canada
Identification	Class I, Zone 2, Ex nA nC IIC Gc T6 X
Corrosive gas test
Identification	ISA-S71.04. G3 Harsh Group
Identification		EN 60068-2-60