PLC-RSC-120UC/21HC/MS - Relay Module Phoenix Contact

Mã sản phẩm: 2910517

Danh mục: PHOENIX CONTACT, Switch, Measure and Monitor Phoenix Contact,

PLC-INTERFACE, consisting of a relay base and pluggable power contact relay with manual operation, integrated status LED, Screw connection, 1 changeover contact, Bridge rectifier, Input voltage: 120 V AC / 110 V DC

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

Product type	Relay Module
Product family	PLC-INTERFACE
Application	Palm switch
Application		High continuous currents
Operating mode	100% operating factor
Mechanical service life	5x 10⁶cycles
Insulation characteristics
Insulation	Safe isolation, reinforced insulation
Insulation characteristics
Insulation	Safe isolation, reinforced insulation
Overvoltage category	III
Pollution degree	2

Maximum power dissipation for nominal condition	0.6 W
Test voltage (Winding/contact)	4 kV_rms (50 Hz, 1 min., winding/contact)
Test voltage (Changeover contact/changeover contact)	2.5 kV_rms (50 Hz, 1 min., changeover contact/changeover contact)
Rated insulation voltage	250 V AC
Rated surge voltage	6 kV

Coil side
Nominal input voltage U_N	120 V AC
Nominal input voltage U_N		110 V DC
Input voltage range	96 V AC ... 168 V AC (20 °C)
Input voltage range		93.5 V DC ... 154 V DC (20 °C)
Typical input current at U_N	5 mA
Typical response time	6 ms (110 V DC)
Typical response time		3 ms ... 15 ms (120 V AC)
Typical release time	8 ms (110 V DC)
Typical release time range	3 ms ... 15 ms (120 V AC)
Protective circuit	Bridge rectifier; Bridge rectifier
Operating voltage display	Yellow LED

Switching
Contact type	1 changeover contact
Type of switch contact	Single contact
Drive and function	monostable
Drive (polarity)	polarized
Contact material	AgNi
Maximum switching voltage	250 V AC/DC (The separating plate PLC-ATP should be installed for voltages larger than 250 V (L1, L2, L3) between identical terminal blocks in adjacent modules. Potential bridging is then carried out with FBST 8-PLC... or ...FBST 500...)
Minimum switching voltage	12 V (10 mA)
Limiting continuous current	10 A
Maximum inrush current	24 A (20 ms)
Min. switching current	10 mA (12 V)
Interrupting rating (ohmic load) max.	264 W (24 V DC)
		62 W (48 V DC)
		48 W (60 V DC)
		52 W (110 V DC)
		66 W (220 V DC)
		2750 VA (250 V AC)
Switching capacity	2 A (24 V, DC13)
Switching capacity		3 A (230 V, AC15)

Connection method	Screw connection
Stripping length	8 mm
Screw thread	M3
Conductor cross section rigid	0.14 mm² ... 2.5 mm²
Conductor cross section flexible	0.14 mm² ... 2.5 mm²
		0.2 mm² ... 2.5 mm² (Single ferrule)
		2x 0.5 mm² ... 1.5 mm² (TWIN ferrule)
Conductor cross section AWG	26 ... 14
Tightening torque	0.6 Nm ... 0.8 Nm

Width	14 mm
Height	80 mm
Depth	104 mm

Flammability rating according to UL 94

V0 (Housing)

Ambient conditions
Degree of protection (Relay)	RT II (Relay)
Degree of protection (Relay base)	IP20 (Relay base)
Degree of protection (Installation location)	≥ IP54 (Installation location)
Ambient temperature (operation)	-40 °C ... 55 °C
Ambient temperature (storage/transport)	-20 °C ... 85 °C
Altitude	≤ 2000 m

UL, USA
Identification	UL 508
		UL 508 Recognized
UL, USA/Canada
Identification	UL 508
		UL 508 Recognized
Corrosive gas test
Identification	ISA-S71.04. G3 Harsh Group
		EN 60068-2-60