PLC-RPT-120UC/21-21/SO46 - Relay Module Phoenix Contact

Mã sản phẩm: 1136244

Danh mục: PHOENIX CONTACT, Switch, Measure and Monitor Phoenix Contact,

PLC-INTERFACE for protection against interference currents or interference voltages on the control side. Consisting of basic terminal block with Push-in connection and plug-in miniature relay with power contact up to 2x 8 A, 2 changeover contacts, 120 V AC input voltage

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

General	The PLC-ATP partition plate must be installed for voltages greater than 250 V (L1, L2, L3) between identical terminal blocks on adjacent modules.
General	The PLC-ATP separating plate should be installed for safe isolation between adjacent modules
General	The system installer must ensure the touch protection of the product (at voltages > 25 V AC/60 V DC). The product is a built-in device without protection against direct contact.
General	The PLC-ATP separating plate is required at the start and end of every PLC terminal strip.

Product type	Relay Module
Product family	PLC-INTERFACE
Application	Filter to prevent interference
Operating mode	100% operating factor
Mechanical service life	approx. 3x 10⁷ cycles
Insulation characteristics
Insulation	Basic insulation
Insulation characteristics: Air clearances and creepage distances between the power circuits
Insulation	Basic insulation
Overvoltage category	III
Pollution degree	3

Maximum power dissipation for nominal condition	0.84 W
Test voltage (Winding/contact)	4 kV_rms (50 Hz, 1 min., winding/contact)
Air clearances and creepage distances between the power circuits
Rated insulation voltage	250 V AC
Rated surge voltage	4 kV (Safe isolation, reinforced insulation, and 6 kV between input circuit and output contact current paths)

Coil side
Nominal input voltage U_N	120 V AC
Nominal input voltage U_N		110 V DC
Input voltage range	94.8 V AC ... 168 V AC (20 °C)
Input voltage range		93.5 V DC ... 168.3 V DC (20 °C)
Mains frequency	50/60 Hz
Typical input current at U_N	6 mA (50 Hz)
Typical input current at U_N		7 mA (60 Hz)
Typical response time	7 ms
Typical release time	10 ms
Typical release voltage	16 V AC
Coil voltage	110 V DC
Protective circuit	RC element
Protective circuit		Bridge rectifier
Status display	Yellow LED

Switching
Contact type	2 changeover contacts
Type of switch contact	Single contact
Drive and function	monostable
Drive (polarity)	polarized
Contact material	AgNi
Maximum switching voltage	250 V AC/DC
Minimum switching voltage	5 V (10 mA)
Limiting continuous current	6 A
Maximum inrush current	15 A (300 ms)
Min. switching current	10 mA (5 V)
Interrupting rating (ohmic load) max.	144 W (24 V DC)
		96 W (48 V DC)
		60 W (60 V DC)
		44 W (110 V DC)
		57 W (220 V DC)
		1500 VA (250 V AC)
Switching capacity min.	0.12 W

Connection method	Push-in connection
Stripping length	10 mm
Conductor cross section rigid	0.14 mm² ... 2.5 mm²
Conductor cross section flexible	0.14 mm² ... 2.5 mm²
		0.2 mm² ... 2.5 mm² (Single ferrule)
		2x 0.5 mm² ... 1 mm² (TWIN ferrule)
Conductor cross section AWG	26 ... 14

Width	14 mm
Height	80 mm
Depth	94 mm

Ambient conditions
Degree of protection (Relay base)	IP20 (Relay base)
Degree of protection (Relay)	RT III (Relay)
Degree of protection (Installation location)	IP54 (Installation location)
Ambient temperature (operation)	-40 °C ... 55 °C
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Altitude	≤ 2000 m