MINI MCR-SL-UI-F - Frequency transducer Phoenix Contact

Mã sản phẩm: 2864082

Danh mục: PHOENIX CONTACT, Switch, Measure and Monitor Phoenix Contact,

Analog frequency transducers for converting analog standard signals into frequency signals or PWM signals, configurable via DIP switch, with screw connection

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

Utilization restriction
EMC note	EMC: class A product, see manufacturer's declaration in the download area

Product type	Frequency value transformer
Product family	MINI Analog
No. of channels	1
Configuration	DIP switches
Insulation characteristics
Overvoltage category	II
Pollution degree	2

Functionality
Configuration	DIP switches

No. of channels	1
Electrical isolation between input and output	yes
Step response (0–99%)	< 15 ms (+ (1/f) smallest filter)
Step response (0–99%)		< 1 s (+ (1/f) largest filter)
Maximum temperature coefficient	< 0.02 %/K
Temperature coefficient, typical	< 0.02 %/K
Maximum transmission error	≤ 0.1 % (> 7 kHz ≤ 0.2 %)
Electrical isolation Input/output/power supply
Rated insulation voltage	30 V AC
Rated insulation voltage		50 V DC
Test voltage	1.5 kV AC (50 Hz, 60 s)
Insulation	Basic insulation in accordance with IEC/EN 61010
Supply
Nominal supply voltage	24 V DC
Supply voltage range	19.2 V DC ... 30 V DC (The DIN rail connector (ME 6,2 TBUS-2 1,5/5-ST-3,81 GN, item no. 2869728) can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail in accordance with EN 60715)
Max. current consumption	< 10 mA (at 24 V DC)
Power consumption	< 200 mW

Signal: Voltage/current
Number of inputs	1
Configurable/programmable	Yes
Voltage input signal	0 V ... 5 V
		1 V ... 5 V
		0 V ... 10 V
		2 V ... 10 V
Max. voltage input signal	30 V DC
Current input signal	0 mA ... 20 mA
		4 mA ... 20 mA
		0 mA ... 10 mA
		2 mA ... 10 mA
Max. current input signal	100 mA
Input resistance of voltage input	approx. 110 kΩ
Input resistance current input	approx. 50 Ω
Behavior in the event of an error	Alarm in the form of a red LED

Frequency: Frequency
Frequency output	0 Hz ... 10 kHz
		0 Hz ... 5 kHz
		0 Hz ... 2.5 kHz
		0 Hz ... 1 kHz
		0 Hz ... 500 Hz
		0 Hz ... 250 Hz
		0 Hz ... 100 Hz
		0 Hz ... 50 Hz
Load min.	4 mA ≤ (U_L / R_L) ≤ 20 mA
Output signal PWM	7.8 kHz (10 bit)
		3.9 kHz (10 bit)
		1.9 kHz (12 bit)
		977 Hz (12 bit)
		488 Hz (14 bit)
		244 Hz (14 bit)
		122 Hz (16 bit)
		61 Hz (16 bit)
Load min.	12 mA ≤ (U_L / R_L) ≤ 20 mA
Load current maximum	20 mA
Maximum switching voltage	30 V
Overrange/underrange	Can be set (via DIP switch)
Protective circuit	Short-circuit protection, polarity reversal protection
Signal
Number of outputs	1

Connection method	Screw connection
Stripping length	12 mm
Screw thread	M3
Conductor cross section rigid	0.2 mm² ... 2.5 mm²
Conductor cross section flexible	0.2 mm² ... 2.5 mm²
Conductor cross section AWG	26 ... 12

Dimensional drawing
Width	6.2 mm
Height	93.1 mm
Depth	101.2 mm

Fire protection for rail vehicles (DIN EN 45545-2) R22	HL 1 - HL 2
Fire protection for rail vehicles (DIN EN 45545-2) R23	HL 1 - HL 2
Fire protection for rail vehicles (DIN EN 45545-2) R24	HL 1 - HL 2
Housing material	PBT

Ambient conditions
Degree of protection	IP20
Ambient temperature (operation)	-20 °C ... 65 °C
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Altitude	≤ 2000 m
Permissible humidity (operation)	5 % ... 95 % (non-condensing)

CE
Certificate	CE-compliant
UKCA
Certificate	UKCA-compliant
UL, USA/Canada
Identification	UL 508 Recognized
Identification		Class I, Div. 2, Groups A, B, C, D T4
Shipbuilding approval
Certificate	DNV GL TAA000020N
DNV GL data
Temperature	B
Humidity	B
Vibration	B
EMC	A
Enclosure	Required protection according to the Rules shall be provided upon installation on board

Noise immunity	EN 61000-6-2
Note	When being exposed to interference, there may be minimal deviations.
Electromagnetic compatibility	Conformance with EMC directive
Noise emission	EN 61000-6-4
Electrostatic discharge
Standards/regulations	EN 61000-4-2
Electrostatic discharge
Comments	Safety measures must be taken to prevent electrostatic discharge.
Electromagnetic HF field
Designation	Electromagnetic RF field
Standards/regulations	EN 61000-4-3
Typical deviation from the measuring range final value	2 %
Fast transients (burst)
Designation	Fast transients (burst)
Standards/regulations	EN 61000-4-4
Typical deviation from the measuring range final value	2 %
Surge current load (surge)
Standards/regulations	EN 61000-4-5
Surge current load (surge)
Comments	Criterion B
Conducted interference
Designation	Conducted interferences
Standards/regulations	EN 61000-4-6
Typical deviation from the measuring range final value	2 %