MINI MCR-SL-PT100-LP-NC - Temperature measuring transducer Phoenix Contact

Mã sản phẩm: 2810308

Danh mục: PHOENIX CONTACT, Switch, Measure and Monitor Phoenix Contact,

Configurable loop-powered temperature transducer for Pt 100 temperature sensors, configured via DIP switches, with screw connection, not pre-configured

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

Utilization restriction
EMC note	EMC: class A product, see manufacturer's declaration in the download area

Product type	Temperature transmitter
Product family	MINI Analog
Configuration	DIP switches
Insulation characteristics
Overvoltage category	II
Pollution degree	2

Linearity error	< 0.05 % (for full measuring range)
Maximum power dissipation for nominal condition	< 42 mW
Step response (0–99%)	< 200 ms
Maximum temperature coefficient	< 0.02 %/K
Transmission error in the set measuring range	((90 K / set measuring range [K]) + 0.05)%
Transmission error in the full measuring range	≤ 0.25 %
Electrical isolation Input/output/power supply
Rated insulation voltage	30 V AC
Rated insulation voltage		50 V DC
Test voltage	1.5 kV AC (50 Hz, 60 s)
Insulation	Basic insulation in accordance with IEC/EN 61010
Supply
Designation	Loop-powered
Supply voltage range	12 V DC ... 30 V DC
Max. current consumption	< 4.5 mA (without signal current)
Power consumption	< 150 mW (without signal current)

Signal
Number of inputs	1
Measurement
Configurable/programmable	Yes, unconfigured
Sensor types (RTD) that can be used	Pt 100 (IEC 60751/EN 60751)
Temperature measuring range	min. 50 K
Sensor type:	-150 °C ... 300 °C (configurable)
Sensor input current	1 mA (constant)
Max. permissible overall conductor resistance	10 Ω (Per cable)
Connection technology	2-, 3-, 4-conductor
Error detection limit (short-circuit)	< 30 Ω
Error detection limit (underrange)	30 Ω ≤ (start span - 2.5% span)
Error detection limit (overrange)	(end span + 2.5% span) ≤ approx. 254 Ω
Error detection limit (wire break)	> approx. 254 Ω

Signal: Current
Number of outputs	1
Configurable/programmable	Yes, unconfigured
Current output signal	4 mA ... 20 mA
Current output signal		20 mA ... 4 mA
Max. current output signal	23 mA (output limit)
Load/output load current output	(U_supply- 12 V) / 22 mA
Ripple	< 20 mV_PP (at 500 Ω)

Connection method	Screw connection
Stripping length	12 mm
Screw thread	M3
Conductor cross section rigid	0.2 mm² ... 2.5 mm²
Conductor cross section flexible	0.2 mm² ... 2.5 mm²
Conductor cross section AWG	26 ... 12

Dimensional drawing
Width	6.2 mm
Height	93.1 mm
Depth	101.2 mm

Fire protection for rail vehicles (DIN EN 45545-2) R22	HL 1 - HL 2
Fire protection for rail vehicles (DIN EN 45545-2) R23	HL 1 - HL 2
Fire protection for rail vehicles (DIN EN 45545-2) R24	HL 1 - HL 2
Housing material	PBT

Ambient conditions
Degree of protection	IP20
Ambient temperature (operation)	-20 °C ... 65 °C
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Altitude	≤ 2000 m
Permissible humidity (operation)	5 % ... 95 % (non-condensing)

CE
Certificate	CE-compliant
UKCA
Certificate	UKCA-compliant
UL, USA/Canada
Identification	UL 508 Recognized
		Class I, Div. 2, Groups A, B, C, D T4

Noise immunity	EN 61000-6-2
Note	When being exposed to interference, there may be minimal deviations.
Electromagnetic compatibility	Conformance with EMC directive
Noise emission	EN 61000-6-4
Electrostatic discharge
Standards/regulations	EN 61000-4-2
Electrostatic discharge
Comments	Safety measures must be taken to prevent electrostatic discharge.
Electromagnetic HF field
Designation	Electromagnetic RF field
Standards/regulations	EN 61000-4-3
Typical deviation from the measuring range final value	5 %
Fast transients (burst)
Designation	Fast transients (burst)
Standards/regulations	EN 61000-4-4
Typical deviation from the measuring range final value	5 %
Surge current load (surge)
Standards/regulations	EN 61000-4-5
Surge current load (surge)
Comments	Criterion B
Conducted interference
Designation	Conducted interferences
Standards/regulations	EN 61000-4-6
Typical deviation from the measuring range final value	5 %