IOA RPSS-I-I/HART/EX - Power/input isolating amplifier Phoenix Contact

Mã sản phẩm: 2908452

Danh mục: PHOENIX CONTACT, Switch, Measure and Monitor Phoenix Contact,

Ex ic repeater power supply and input signal conditioner, HART for VIP I/O-Marshalling base elements: Transmits 0/4 ... 20 mA signals from the potentially explosive area (zone 2, CID2) to a load (active or passive) in the safe area. 3-way electrical isolation

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

Product type	Repeater power supplies
No. of channels	1
Insulation characteristics
Overvoltage category	II
Degree of pollution	2

No. of channels	1
Electrical isolation	Reinforced insulation in accordance with IEC 61010-1
Limit frequency (3 dB)	1.75 kHz (typ.)
Step response (10-90%)	< 200 µs (typ.)
Maximum temperature coefficient	0.01 %/K
Temperature coefficient, typical	0.01 %/K
Maximum transmission error	< 0.1 % (of final value)
Electrical isolation Input/output/power supply
Electrical isolation	250 V_rms (Rated insulation voltage (overvoltage category II; degree of pollution 2, safe isolation as per EN 61010-1))
		2.5 kV (50 Hz, 1 min., test voltage)
		60 V (Peak value in accordance with IEC/EN 60079-11)
Supply
Nominal supply voltage	24 V DC
Supply voltage range	18 V DC ... 30 V DC
Power consumption	≤ 1600 mW (at I_OUT = 20 mA, 24 V DC, 600 Ω load)

Signal
Input signal	Current
Current input signal	4 mA ... 20 mA (repeater power supply and isolator operation)
Current input signal		0 mA ... 20 mA (isolator operation)
Transmitter supply voltage	> 17 V (20 mA)
Step response (10-90%)	typ. 300 µs (4 mA ... 20 mA)
Step response (10-90%)		typ. 1000 µs (0 mA ... 20 mA)

Signal
Output description	Current output (active and passive)
Current output signal	0 mA ... 20 mA (isolator amplifier)
Current output signal		4 mA ... 20 mA (repeater power supply and isolator operation)
Max. current output signal	22.5 mA
Transmission Behavior	1:1 to input signal
Load/output load current output	≤ 600 Ω (20 mA)
Load/output load current output		525 Ω (22.5 mA)
Residual ripple	< 20 mV_rms (600 Ω)
Output ripple	< 20 mV_rms (at 600 Ω)
Output behavior in the event of an error	0 mA (Cable break in the input)
Output behavior in the event of an error		≥ 22.5 mA (Cable short-circuit in the input)
Underload/overload signal range	0 mA ... 22.5 mA (According to NE43)

Connection method	Screw connection
Stripping length	10 mm
Screw thread	M3
Conductor cross section rigid	0.2 mm² ... 1.5 mm² (with ferrule)
Conductor cross section rigid		0.2 mm² ... 2.5 mm² (without ferrule)
Conductor cross section flexible	0.2 mm² ... 1.5 mm²
Conductor cross section AWG	24 ... 12 (flexible)

Safety data
Input voltage U_i	0 V (nA, nB)
		30 V (nC, nD)
		30 V (Controller interface)
Input current I_i	100 mA (Controller interface)
Inductance Li	0 mH
Capacitance Ci	0 nF
Max. output voltage U_o	28 V (nA, nB)
Max. output voltage U_o		0 V (nC, nD)
Max. output current I_o	104 mA
Max. output power P_o	726 mW
Safety-related maximum voltage U_m	60 V AC/DC (Peak)
IIC: Max. external inductivity L_o / Max. external capacitance C_o	/ 0.27 µF
IIB/IIIC/IIIB/IIIA: Max. external inductivity L_o / Max. external capacitance C_o	/ 1.65 µF
IIA: Max. external inductivity L_o / Max. external capacitance C_o	/ 6.6 µF
IIC: Max. external inductivity L_o / Max. external capacitance C_o	7.3 mH
IIB/IIIC/IIIB/IIIA: Max. external inductivity L_o / Max. external capacitance C_o	14.7 mH
IIA: Max. external inductivity L_o / Max. external capacitance C_o	29.5 mH

Data communication (bypass)
HART function	Yes
Protocols supported	HART
Limit frequency (3 dB)	> 1.75 kHz (typical)

Status display

Green LED (supply voltage)

Width	9.8 mm
Height	75.2 mm
Depth	113.2 mm

Flammability rating according to UL 94

Ambient conditions
Degree of protection	IP20
Ambient temperature (operation)	-40 °C ... 70 °C
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Altitude	2000 m (max. altitude above sea level)
Permissible humidity (operation)	5 % ... 95 %

ATEX
Identification	II 3G Ex ec IIC T4 Gc
		II 3G Ex ec [ic] IIC T4 Gc
		II (3)D [Ex ic IIIC Dc]
Certificate	Sira 17ATEX4208X
IECEx
Identification	Ex ec IIC T4 Gc
		Ex ec [ic] IIC T4 Gc
		[Ex ic IIIC Dc]
Certificate	IECEx SIR 17.0047X
FM
Identification	Non-incendive Class I, Div. 2 Groups A, B, C, D, T4
		ANIFW apparatus for connection to: Class I, II, III, Div. 2 Groups A, B, C, D, E, F, G
		Class I, Zone 2 AEx nA IIC T4 Gc
		Class I, Zone 2 AEx ec IIC T4 Gc
CSA, USA/Canada
Identification	Class I, Div. 2 Groups A, B, C, D T4
		ANIFW apparatus for connection to: Class I, II, III, Div. 2 Groups A, B, C, D, E, F, G
		Class I, Zone 2 AEx ec IIC T4 Gc
		AEx ec [ic] IIC T4 Gc
		Connection to Zone 22, [Ex ic IIIC Dc]
		Connection to: Class I, II, III Div. 2 Groups A, B, C, D, E, F, G
		Ex ec IIC T4 Gc
		Ex ec [ic] IIC T4 Gc
		[Ex ic IIIC Dc]
Corrosive gas test
Identification	ISA S71.04.2013 G3 Harsh Group A

Electromagnetic compatibility	Conformance with EMC directive
Electromagnetic HF field
Designation	Electromagnetic RF field
Standards/regulations	EN 61000-4-3
Typical deviation from the measuring range final value	1 %
Fast transients (burst)
Designation	Fast transients (burst)
Standards/regulations	EN 61000-4-4
Typical deviation from the measuring range final value	1 %
Conducted interference
Designation	Conducted interferences
Standards/regulations	EN 61000-4-6
Typical deviation from the measuring range final value	1 %