VS-FSBPYS-OE-94H/0,5 SCO - Device connector, rear mounting Phoenix Contact

Mã sản phẩm: 1407504

Danh mục: PHOENIX CONTACT, Kết nối (Connect) Phoenix Contact 2,

Device connector, rear mounting, Ethernet hybrid CAT5 (100 Mbps) CAT5 (100 Mbps), 8-position, Flush-type female connector, straight, M12-SPEEDCON, coding: Y , on free cable end, Rear mounting, M16 x 1.5, Hybrid cable, cable length: 0.5 m, Alternative product in accordance with RoHS II without Exemption 6c (Pb <0.1%) item no.: 1238749

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

General	The electrical and mechanical data specified assume that the connector pair is correctly locked and mounted. If the connector is unlocked and if there is a danger of contamination, the connector must be sealed using a protective cap > IP54. Influences arising from litz wires, cables or PCB assembly must also be taken into consideration.
Safety note
Safety note	WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
		• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
		• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
		• The products are suitable for applications in plant, controller, and electrical device engineering.
		• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
		• Assembled products may not be manipulated or improperly opened.
		• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
		• When using the product in direct connection with third-party manufacturers, the user is responsible.
		• For operating voltages > 50 V AC, conductive connector housings must be grounded
		• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
		• Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product
		• Only use tools recommended by Phoenix Contact
		• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
		• Ensure that the protective or functional ground has been properly connected.
		• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
		• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Mounting type	Rear mounting M16 x 1.5
Connection method	Hybrid cable

Product type	Circular connectors (device side)
Number of positions	8
Sensor type	Ethernet hybrid
No. of cable outlets	1
Shielded	yes
Coding	Y
Insulation characteristics
Overvoltage category	III
Degree of pollution	3

Material	Zinc die-cast (nickel-plated)
Flammability rating according to UL 94	V0
Seal material	FKM
Contact material	CuZn
Contact surface material	Ni/Au
Contact carrier material	PA 6.6
Material for screw connection	Nickel-plated brass

Contact resistance	≤ 3 mΩ
Insulation resistance	≥ 100 MΩ
Nominal voltage U_N	48 V AC (Power and data)
Nominal voltage U_N		50 V DC (Power and data)
Nominal current I_N	0.5 A (Data)
Nominal current I_N		6 A (Power)
Transmission medium	Copper
Transmission characteristics (category)	CAT5

Conductor connection
Connection method	Hybrid cable
Type of contact	Crimp contacts
Tightening torque	2 Nm
Tightening torque		3 Nm

Mechanical data
Insertion/withdrawal cycles	> 100

Connection 1
Head design	Flush-type female connector
Head cable outlet	straight
Head thread type	M12
Head locking type	SPEEDCON
Coding	Y
Connection 2
Head design	free cable end

Cable length	0.5 m
Ethernet hybrid [94H]
Cable weight	87 kg/km
UL AWM Style	21815 (80°C/300 V)
Number of positions	8
Shielded	yes
Cable type	Ethernet hybrid [94H]
Conductor structure	1x4xAWG26+1x4xAWG20
Conductor structure signal line	19x 0.10 mm
AWG signal line	26
Conductor cross section	4x 0.15 mm² (Data)
Conductor cross section		4x 0.6 mm² (Power)
Wire diameter incl. insulation	1.05 mm (Data)
Wire diameter incl. insulation		1.4 mm (Power)
External cable diameter	7.6 mm ±0.2 mm
Outer sheath, material	PUR
External sheath, color	black RAL 9005
Conductor material	Bare Cu litz wires
Material wire insulation	PP (Data)
Material wire insulation		PP (Power)
Single wire, color	white/orange, orange, white/green, green, white, blue, brown, black
Overall twist	1 star quad and 4 wires with 2 fillers
Optical shield covering	85 %
Insulation resistance	≥ 5 GΩ*km
Loop resistance	≤ 280.00 Ω/km (Data)
Loop resistance		≤ 34.60 Ω/km (Power)
Wave impedance	100 Ω ±15 Ω (4 MHz ... 100 MHz)
Working capacitance	nom. 50 nF (per kilometer)
Differential impedance	100 Ω ±5 % (at 100 MHz)
Nominal voltage, cable	≤ 300 V (Peak value, not for high-power applications)
Test voltage Core/Core	2000 V (50 Hz, 1 min.)
Test voltage Core/Shield	2000 V (50 Hz, 1 min.)
Minimum bending radius, fixed installation	5 x D
Minimum bending radius, flexible installation	10 x D
Max. bending cycles	2000000
Tensile strength	70 N (in accordance with DIN EN 50565-1 for flexible installation)
Tensile strength		240 N (in accordance with DIN EN 50565-1 for fixed installation)
Near end crosstalk attenuation (NEXT)	56.3 dB (at 4 МHz)
		50.3 dB (at 10 MHz)
		47.2 dB (at 16 MHz)
		45.8 dB (at 20 МHz)
		42.9 dB (at 31.25 МHz)
		38.4 dB (at 62.5 МHz)
		35.3 dB (at 100 MHz)
Shield attenuation	6 dB (at 4 МHz)
		9.5 dB (at 10 MHz)
		12.1 dB (at 16 MHz)
		13.5 dB (at 20 МHz)
		17.1 dB (at 31.25 МHz)
		24.8 dB (at 62.5 МHz)
		32 dB (at 100 MHz)
		≥ 80 dB (30 MHz ... 125 MHz)
Halogen-free	according to IEC 60754
Halogen-free		in accordance with DIN VDE 0472 part 815
Flame resistance	in accordance with UL 2556, Section 9.1 and UL 1581, Section 1100
Flame resistance		in accordance with UL 2556, Section 9.3 and UL 1581, Section 1060
Resistance to oil	in accordance with IEC 60811-404
Resistance to oil		According to DIN EN 50363-10-2
Other resistance	Low adhesion
Special properties	Free of substances which would hinder coating with paint or varnish
Special properties		Silicone-free
Ambient temperature (operation)	-40 °C ... 80 °C (cable, fixed installation)
Ambient temperature (operation)		-30 °C ... 70 °C (Cable, flexible installation)

Ambient conditions
Degree of protection	IP67
		IP65/IP67
Ambient temperature (operation)	-25 °C ... 80 °C (Plug / socket)
		-40 °C ... 80 °C (without mechanical actuation)