VS-FSBPXS-OE-94F/2,0 - Device connector, rear mounting Phoenix Contact

Mã sản phẩm: 1424151

Danh mục: PHOENIX CONTACT, Kết nối (Connect) Phoenix Contact 2,

Device connector, rear mounting, Ethernet CAT6A (10 Gbps) CAT6A, 8-position, PUR, water blue RAL 5021, shielded, Flush-type female connector, straight, M12-SPEEDCON, coding: X , on free cable end, Rear mounting, M16 x 1.5, Bus line, cable length: 2 m, Ethernet 10 Gbit, Alternative product in accordance with RoHS II without Exemption 6c (Pb <0.1%) item no.: 1239448

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

General	The electrical and mechanical data specified assume that the connector pair is correctly locked and mounted. If the connector is unlocked and if there is a danger of contamination, the connector must be sealed using a protective cap > IP54. Influences arising from litz wires, cables or PCB assembly must also be taken into consideration.
Safety note
Safety note	WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
		• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
		• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
		• The products are suitable for applications in plant, controller, and electrical device engineering.
		• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
		• Assembled products may not be manipulated or improperly opened.
		• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
		• When using the product in direct connection with third-party manufacturers, the user is responsible.
		• For operating voltages > 50 V AC, conductive connector housings must be grounded
		• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
		• Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product
		• Only use tools recommended by Phoenix Contact
		• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
		• Ensure that the protective or functional ground has been properly connected.
		• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
		• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Product type	Data cable preassembled
Number of positions	8
Sensor type	Ethernet
Application	Railway applications
No. of cable outlets	1
Shielded	yes
Coding	X
Insulation characteristics
Overvoltage category	III
Degree of pollution	3

Bus system	Ethernet
Signal type/category	Ethernet CAT6_A, 10 Gbps

Rated surge voltage	0.8 kV
Contact resistance	≤ 3 mΩ
Insulation resistance	≥ 100 MΩ
Nominal voltage U_N	50 V AC
Nominal voltage U_N		60 V DC
Nominal current I_N	0.5 A (Plug/socket in accordance with IEC 61076-2-101, cable technical data is to be observed)
Transmission medium	Copper
Transmission characteristics (category)	CAT6_A

Mechanical data
Insertion/withdrawal cycles	≥ 100

Flammability rating according to UL 94	V0
Seal material	FKM
Contact material	CuZn
Contact surface material	Au
Contact carrier material	PPA
Material for screw connection	Zinc die-cast, nickel-plated
Outer sheath, material	PUR

Connection technology
Connection method	Bus line
Conductor connection
Type of contact	Crimp contacts
Connection method	Bus line
Tightening torque	2 Nm ... 3 Nm (Installation-side)

Connection 1
Head design	Flush-type female connector
Head cable outlet	straight
Head thread type	M12
Head locking type	SPEEDCON
Coding	X
Connection 2
Head design	free cable end

Cable length	2 m
Ethernet 10 Gbit [94F]
Dimensional drawing
Cable weight	42 kg/km
UL AWM Style	20963 (80°C/30 V)
Number of positions	8
Shielded	yes
Cable type	Ethernet 10 Gbit [94F]
Conductor structure	4x2xAWG26/7; S/FTP
Signal runtime	5.13 ns/m
Conductor structure signal line	7x 0.16 mm
AWG signal line	26
Conductor cross section	4x 2x 0.14 mm²
Wire diameter incl. insulation	1.04 mm
External cable diameter	6.4 mm ±0.2 mm
Outer sheath, material	PUR
External sheath, color	water blue RAL 5021
Conductor material	Bare Cu litz wires
Material wire insulation	Foamed PE
Single wire, color	white/blue-blue, white/orange-orange, white/green-green, white/brown-brown
Thickness, outer sheath	0.65 mm
Twisted pairs	2 cores to the pair
Type of pair shielding	Aluminum-lined foil
Overall twist	4 pairs for core
Optical shield covering	70 %
Insulation resistance	≥ 500 MΩ*km
Loop resistance	≤ 290.00 Ω/km
Wave impedance	100 Ω ±5 Ω (at 100 MHz)
Cable capacity	47 nF/km
Nominal voltage, cable	≤ 100 V
Test voltage Core/Core	700 V (50 Hz, 1 min.)
Test voltage Core/Shield	700 V (50 Hz, 1 min.)
Minimum bending radius, fixed installation	4 x D
Minimum bending radius, flexible installation	8 x D
Tensile strength	≤ 100 N
Near end crosstalk attenuation (NEXT)	75.3 dB (with 1 MHz)
		66.3 dB (at 4 МHz)
		61.8 dB (at 8 МHz)
		60.3 dB (at 10 MHz)
		57.2 dB (at 16 MHz)
		55.8 dB (at 20 МHz)
		54.3 dB (at 25 MHz)
		52.8 dB (at 31.25 МHz)
		48.4 dB (at 62.5 МHz)
		45.3 dB (at 100 MHz)
		40.8 dB (at 200 MHz)
		39.3 dB (at 250 MHz)
		38.1 dB (at 300 MHz)
		36.3 dB (at 400 MHz)
		34.8 dB (at 500 MHz)
Power-summated near end crosstalk attenuation (PSNEXT)	72.3 dB (with 1 MHz)
		63.3 dB (at 4 МHz)
		58.8 dB (at 8 МHz)
		57.3 dB (at 10 MHz)
		54.2 dB (at 16 MHz)
		52.8 dB (at 20 МHz)
		51.3 dB (at 25 MHz)
		49.9 dB (at 31.25 МHz)
		45.4 dB (at 62.5 МHz)
		42.3 dB (at 100 MHz)
		37.8 dB (at 200 MHz)
		36.3 dB (at 250 MHz)
		35.1 dB (at 300 MHz)
		33.3 dB (at 400 MHz)
		31.8 dB (at 500 MHz)
Return loss (RL)	20 dB (with 1 MHz)
		23 dB (at 4 МHz)
		24.5 dB (at 8 МHz)
		25 dB (at 10 MHz)
		25 dB (at 16 MHz)
		25 dB (at 20 МHz)
		24.2 dB (at 25 MHz)
		23.3 dB (at 31.25 МHz)
		20.7 dB (at 62.5 МHz)
		19 dB (at 100 MHz)
		16.4 dB (at 200 MHz)
		15.6 dB (at 250 MHz)
		15.6 dB (at 300 MHz)
		15.6 dB (at 400 MHz)
		15.6 dB (at 500 MHz)
Shield attenuation	3.1 dB (with 1 MHz)
		5.7 dB (at 4 МHz)
		8 dB (at 8 МHz)
		8.9 dB (at 10 MHz)
		11.2 dB (at 16 MHz)
		12.6 dB (at 20 МHz)
		14.1 dB (at 25 MHz)
		15.8 dB (at 31.25 МHz)
		22.5 dB (at 62.5 МHz)
		28.7 dB (at 100 MHz)
		41.4 dB (at 200 MHz)
		46.6 dB (at 250 MHz)
		51.4 dB (at 300 MHz)
		60.1 dB (at 400 MHz)
		67.9 dB (at 500 MHz)
		≥ 80 dB (at 30 ... 100 MHz)
Halogen-free	according to IEC 60754-1
Flame resistance	according to IEC 60332-1-2
Resistance to oil	in accordance with DIN EN 60811-2-1
Ambient temperature (operation)	-40 °C ... 80 °C (cable, fixed installation)
Ambient temperature (operation)		-20 °C ... 80 °C (Cable, flexible installation)
Ambient temperature (installation)	-20 °C ... 80 °C

Ambient conditions
Degree of protection	IP67
		IP65
		IP65/IP67
Ambient temperature (operation)	-25 °C ... 85 °C (Plug / socket)
Ambient temperature (operation)		-40 °C ... 85 °C (without mechanical actuation)