VC-FSMA-M-KT-2 SET - Fiber optic contact insert Phoenix Contact

Mã sản phẩm: 1855703

Danh mục: PHOENIX CONTACT, Kết nối (Connect) Phoenix Contact,

FO connector (cable side), Range of articles: VARIOCON, Fiber optic contact insert, design: FSMA, housing material: Nickel silver, color: light grey, number of positions: 1

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

Safety note
Safety note	WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
		• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
		• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
		• The products are suitable for applications in plant, controller, and electrical device engineering.
		• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
		• Assembled products may not be manipulated or improperly opened.
		• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
		• When using the product in direct connection with third-party manufacturers, the user is responsible.
		• For operating voltages > 50 V AC, conductive connector housings must be grounded
		• Ensure that the protective or functional ground has been properly connected.
		• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
		• Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product
		• Only use tools recommended by Phoenix Contact
		• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
		• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
		• Operate the connector only when it is fully plugged in.
		• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
		• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
		• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Type	FSMA
Product type	Fiber optic connector (cable side)
Product family	VARIOCON
Number of positions	1
Connection profile	F-SMA type 905, IEC 874-2

Attenuation

≤ 1.5 dB (at 650 nm (for each plug))

Dimensional drawing
Width	7 mm
Height	7 mm
Length	71 mm
Mechanical characteristics
Contact diameter	3.1 mm

Color	light grey
Material	Polyamide
Contact material	Nickel silver
Housing material	Nickel silver

Cable type	Polymer fiber (980 / 1000 µm)
External cable diameter	≤ 2.3 mm
Resistance to oil	yes
Flame resistance	yes
FO cable
Number of fibers	2
Fiber	Polymer fiber, 980/1000 µm
Fiber type	POF fiber A4A
Transmission medium	FO

Mechanical data
Insertion/withdrawal cycles	> 100

Attenuation

≤ 1.5 dB (at 650 nm (for each plug))

Ambient conditions
Degree of protection	IP20
Degree of protection		IP20
Ambient temperature (operation)	-20 °C ... 70 °C
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Ambient temperature (assembly)	-5 °C ... 50 °C
Resistance to oil	yes