UNO2-PS/1AC/48DC/240W - Power supply unit Phoenix Contact

Mã sản phẩm: 1110155

Danh mục: PHOENIX CONTACT, Supply, charge, and protect Phoenix Contact,

Primary-switched power supply unit, UNO POWER, Screw connection, DIN rail mounting, input: 1-phase, output: 48 V DC / 5 A

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

AC operation
Supply system configuration	Star network (TN, TT, IT (PE))
Nominal input voltage range	100 V AC ... 240 V AC
Input voltage range	100 V AC ... 240 V AC -15 % ... +10 %
Derating	< 90 V AC (1 %/V)
Typical national grid voltage	120 V AC
Typical national grid voltage		230 V AC
Voltage type of supply voltage	AC
Inrush current	typ. 10 A (at 25 °C)
Inrush current integral (I²t)	< 0.05 A²s
Frequency range (f_N)	50 Hz ... 60 Hz ±10 %
Mains buffering time	typ. 20 ms (120 V AC)
Mains buffering time		typ. 20 ms (230 V AC)
Current consumption	2.6 A (100 V AC)
		2.2 A (120 V AC)
		1.16 A (230 V AC)
		1.2 A (240 V AC)
Protective circuit	Transient surge protection; Varistor, gas-filled surge arrester
Switch-on time	typ. 530 ms
Device mains fuse	5 A internal (device protection), fast-blow
Recommended breaker for input protection	10 A ... 16 A (Characteristic B, C, D, K or comparable)
Discharge current to PE	< 3.5 mA

Efficiency	typ. 91.5 % (120 V AC)
Efficiency		typ. 93 % (230 V AC)
Nominal output voltage	48 V DC
Setting range of the output voltage (U_Set)	42 V DC ... 56 V DC (≥48 V DC, constant capacity restricted<48 V DC, constant current restricted)
Nominal output current (I_N)	5 A
Short-circuit-proof	yes
No-load proof	yes
Crest factor	typ. 1.637 (120 V AC)
Crest factor		typ. 1.54 (230 V AC)
Output power (P_N)	240 W
Connection in parallel	yes, for redundancy
Connection in series	yes, for increased output voltage
Feedback voltage resistance	≤ 60 V DC
Protection against overvoltage at the output (OVP)	≤ 60 V DC
Residual ripple	typ. 50 mV_PP (with nominal values)
Control deviation	< 1 % (change in load, static 10 % ... 90 %)
		< 3 % (change in load, dynamic 10 % ... 90 %)
		< 0.1 % (change in input voltage ±10 %)
Rise time	< 1 s (U_Out = 10 % ... 90 %)
Minimum no-load power dissipation	< 2.9 W (120 V AC)
Maximum no-load power dissipation	< 3 W (230 V AC)
Minimum nominal load power dissipation	< 37 W (120 V AC)
Power loss nominal load max.	< 28 W (230 V AC)
Signal relay 13/14
Connection level	3.x
Connection labeling	3.1 (13), 3.2 (14)
Switch contact (floating)	OptoMOS
Switching voltage	max. 30 V AC/DC
Switching voltage		max. 60 V DC
Current carrying capacity	max. 50 mA
State condition	U_OUT ≥ 0.9 x U_N (U_N = 48 V DC) (Contact closed)
		U_OUT < 42 V DC (Contact open)
		U_OUT > 60 V DC (Contact open)

Input
Position	1.x
Identification	1.1 (), 1.2 (L), 1.3 (N)
Conductor connection
Connection method	Screw connection
rigid	0.2 mm² ... 2.5 mm²
flexible	0.2 mm² ... 2.5 mm²
flexible with ferrule without plastic sleeve	0.25 mm² ... 2.5 mm²
flexible with ferrule with plastic sleeve	0.25 mm² ... 2.5 mm²
rigid (AWG)	24 ... 14 (Cu)
Stripping length	6.5 mm
Tightening torque	0.5 Nm ... 0.6 Nm
Tightening torque		4 lb_f-in. ... 5 lb_f-in.
Drive form screw head	Slotted L
Output
Position	2.x
Identification	2.1, 2.2 (+), 2.3, 2.4 (-)
Conductor connection
Connection method	Screw connection
rigid	0.2 mm² ... 2.5 mm²
flexible	0.2 mm² ... 2.5 mm²
flexible with ferrule without plastic sleeve	0.25 mm² ... 2.5 mm²
flexible with ferrule with plastic sleeve	0.25 mm² ... 2.5 mm²
rigid (AWG)	24 ... 14 (Cu)
Stripping length	6.5 mm
Tightening torque	0.5 Nm ... 0.6 Nm
Tightening torque		4 lb_f-in. ... 5 lb_f-in.
Drive form screw head	Slotted L
Signal
Position	3.x
Identification	3.1 (13), 3.2 (14)
Conductor connection
Connection method	Screw connection
rigid	0.2 mm² ... 2.5 mm²
flexible	0.2 mm² ... 2.5 mm²
flexible with ferrule without plastic sleeve	0.25 mm² ... 2.5 mm²
flexible with ferrule with plastic sleeve	0.25 mm² ... 2.5 mm²
rigid (AWG)	24 ... 14 (Cu)
Stripping length	6.5 mm
Tightening torque	0.5 Nm ... 0.6 Nm
Tightening torque		4 lb_f-in. ... 5 lb_f-in.
Drive form screw head	Slotted L

Types of signaling	DC OK LED - signal state operation (U_N = 48 V DC, I_Out = I_N)
Function	Visual operating state display
Color	green
LED off	Input AC supply voltage not available or U_Out< 0.9 x U_N (U_N = 48 V DC) (Off)
LED on (green), DC OK	U_OUT ≥ 0.9 x U_N (U_N = 48 V DC) (On (green), DC OK)
LED on (flashing green) DC OK < 0.9 x UN	U_OUT > 60 V DC (on (flashing green))

Number of phases	1.00
Insulation voltage input/output	4 kV AC (type test)
Insulation voltage input/output		3 kV AC (routine test)
Insulation voltage input / PE	3.5 kV AC (type test)
Insulation voltage input / PE		2.4 kV AC (routine test)

Product type	Power supply
Product family	UNO POWER
MTBF (IEC 61709, SN 29500)	> 1000000 h (25 °C)
		> 550000 h (40 °C)
		> 280000 h (55 °C)
Environmental protection directive	RoHS Directive 2011/65/EU
		WEEE
		Reach
Insulation characteristics
Protection class	I
Degree of pollution	2

Dimensional drawing
Width	45 mm
Height	130 mm
Depth	129 mm
Depth Device depth (DIN rail mounting)	125 mm (Device depth (DIN rail mounting))
Installation dimensions
Installation distance right/left (active, passive)	0 mm / 0 mm (P_Out ≥50% )
Installation distance top/bottom (active, passive)	30 mm / 30 mm (P_Out ≥50% )

Mounting type	DIN rail mounting
Assembly instructions	alignable: 0 mm horizontally, 30 mm vertically
Mounting position	horizontal DIN rail NS 35, EN 60715
With protective coating	No

Flammability rating according to UL 94	V0 (Housing, terminal blocks)
Housing material	Metal
Hood version	Stainless steel
Side element version	Aluminum
Foot latch material	Sheet steel, zinc-plated
Housing material	Aluminum (AlMg3) / sheet steel, zinc-plated

Ambient conditions
Degree of protection	IP20
Ambient temperature (operation)	-25 °C ... 70 °C (> 55 °C Derating: 2.5 %/K)
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Ambient temperature (start-up type tested)	-40 °C
Maximum altitude	≤ 3000 m (> 2000 m, Derating: 10 %/1000 m)
Max. permissible relative humidity (operation)	≤ 95 % (at 25 °C, non-condensing)
Shock (operation)	18 ms, 30g, per spatial direction (IEC 60068-2-27)
Vibration (operation)	10 Hz ... 50 Hz, amplitude ±0.2 mm
Vibration (operation)		50 Hz to 150 Hz, 2.3 g, 90 min.

Overvoltage category
EN 61010-1	II (≤ 3000 m)
Overvoltage category
EN 62477-1	III (≤3000 m)
Safety of power supply units up to 1100 V (insulation distances)
Standards/specifications	DIN EN 61558-2-16
Electrical safety
Standards/specifications	IEC 61010-2-201 (SELV)
Electronic equipment for use in power installations
Standards/specifications	EN 50178/VDE 0160 (PELV)
Safety for measurement, control, and laboratory equipment
Standards/specifications	IEC 61010-1
Protective extra-low voltage
Standards/specifications	IEC 61010-1 (SELV)
		IEC 61010-2-201 (PELV)
Safe isolation
Standards/specifications	IEC 61558-2-16
		IEC 61010-2-201
Limitation of harmonic line currents
Standards/specifications	EN 61000-3-2
Mains voltage dips
Standards/specifications	SEMI F47 - 0706 (185 V AC)

UL
Identification	UL/C-UL Listed UL 61010-1
UL
Identification	UL/C-UL Listed UL 61010-2-201
UL
Identification	UL/C-UL Listed ANSI/UL 121201 Class I, Division 2, Groups A, B, C, D (Hazardous Location)
SIQ
Identification	CB scheme (IEC 61010-1, IEC 61010-2-201)

Low Voltage Directive	Conformance with Low Voltage Directive 2014/35/EC
Interference emission	Interference emission in accordance with EN 61000-6-3 (residential and commercial) and EN 61000-6-4 (industrial)
EMC requirements for noise immunity	EN 61000-6-2
Electromagnetic compatibility	Conformance with EMC Directive 2014/30/EU
Conducted noise emission	EN 55016
Conducted noise emission		EN 61000-6-3 (Class B)
Noise emission	EN 55016
Noise emission		EN 61000-6-3 (Class B)
Harmonic currents
Standards/regulations	EN 61000-3-2
Standards/regulations		EN 61000-3-2 (Class A)
Frequency range	0 kHz ... 2 kHz
Flicker
Standards/regulations	EN 61000-3-3
Frequency range	0 kHz ... 2 kHz
Electrostatic discharge
Standards/regulations	EN 61000-4-2
Electrostatic discharge
Contact discharge	6 kV (Test Level 3)
Discharge in air	8 kV (Test Level 3)
Comments	Criterion A
Electromagnetic HF field
Standards/regulations	EN 61000-4-3
Electromagnetic HF field
Frequency range	80 MHz ... 1 GHz
Test field strength	10 V/m (Test Level 3)
Frequency range	1 GHz ... 6 GHz
Test field strength	10 V/m (Test Level 3)
Comments	Criterion A
Fast transients (burst)
Standards/regulations	EN 61000-4-4
Fast transients (burst)
Input	4 kV (Test Level 4 - asymmetrical)
Output	2 kV (Test Level 3 - asymmetrical)
Comments	Criterion A
Surge voltage load (surge)
Standards/regulations	EN 61000-4-5
Input	2 kV (Test Level 4 - symmetrical)
Input		4 kV (Test Level 4 - asymmetrical)
Output	1 kV (Test Level 3 - symmetrical)
Output		2 kV (Test Level 3 - asymmetrical)
Comments	Criterion A
Conducted interference
Standards/regulations	EN 61000-4-6
Conducted interference
Input/Output	asymmetrical
Frequency range	0.15 MHz ... 80 MHz
Comments	Criterion A
Voltage	10 V (Test Level 3)
Voltage dips
Standards/regulations	EN 61000-4-11
Voltage	230 V AC
Frequency	50 Hz
Voltage dip	70 %
Number of periods	25 / 30 periods
Comments	Criterion A
Voltage dip	40 %
Number of periods	12 periods
Additional text	Test Level 2
Comments	Criterion A
Voltage dip	0 %
Number of periods	1 period
Additional text	Test Level 2
Comments	Criterion B
Criteria
Criterion A	Normal operating behavior within the specified limits.
Criterion B	Temporary impairment to operational behavior that is corrected by the device itself.