UM- D37SUB/M/HC3/16DO/MR/MT - Active module Phoenix Contact

Mã sản phẩm: 2900068

Danh mục: PHOENIX CONTACT, Kết nối (Connect) Phoenix Contact,

16-channel relay module (1 changeover contact) for Honeywell C300 output modules. On the control side, the module is controlled via D-SUB 37-pos. or FLK 50-pos. A screw connection with knife disconnection is available on the field side.

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

General	Do not connect adjacent channels to SELV/ PELV and voltages dangerous to the touch.
General	The outputs are not suitable for switching different outer conductors.
General	Against adjacent modules in the support rail direction at least one functional insulation on the output-side is complied with. If the application has higher requirements on the insulation (basic insulation or reinforced insulation), then these must be realized through suitable measures (e. g. partition plates).

Product type	Interface module
No. of channels	16
Operating mode	100% operating factor
Mechanical service life	2x 10⁷ cycles
Insulation characteristics
Insulation	Reinforced insulation
Insulation characteristics: Air clearances and creepage distances, input/output
Insulation	Reinforced insulation
Overvoltage category	III
Pollution degree	2
Insulation characteristics: Air and creepage distances, output/output
Insulation	Basic insulation
Overvoltage category	III
Pollution degree	2

No. of channels	16
Air clearances and creepage distances, input/output
Rated insulation voltage	300 V
Rated surge voltage	6 kV (1.2/50 μs)
Air and creepage distances, output/output
Rated insulation voltage	300 V
Rated surge voltage	4 kV (1.2/50 μs)
Supported controller HONEYWELL Experion PKS C300/C-Series
Suitable I/O card	TDOB01 (non-redundant)
Suitable I/O card		TDOB11 (redundant)

Nominal input voltage U_N	24 V DC
Input voltage range in reference to U_N	0.85 ... 1.1
Input voltage range	20.4 V DC ... 26.4 V DC
Typical input current at U_N	9 mA
Typical response time	5 ms
Typical release time	7 ms
Protective circuit	Freewheeling diode
Status display/channel	Yellow LED

Switching
Contact type	1 changeover contact
Type of switch contact	Single contact
Contact material	AgSnO
Maximum switching voltage	250 V AC/DC
Minimum switching voltage	12 V AC/DC
Limiting continuous current	4 A (see derating curve)
Min. switching current	10 mA
Interrupting rating (ohmic load) max.	96 W (at 24 V DC)
		20 W (at 48 V DC)
		18 W (at 60 V DC)
		23 W (at 110 V DC)
		40 W (at 220 V DC)
		1000 VA (for 250 V AC)

Controller level
Connection method	D-SUB pin strip
Number of connections	1
Number of positions	37
Field level
Connection method	Screw connection with disconnect knife
Stripping length	8 mm
Screw thread	M3
Conductor cross section rigid	0.2 mm² ... 4 mm²
Conductor cross section flexible	0.2 mm² ... 2.5 mm²
Conductor cross section AWG	24 ... 12
Control side
Connection method	Flat-ribbon cable connector in acc. with IEC 60603-13
Number of connections	1
Number of positions	50

Status display present

Yes

Width	259 mm
Height	126 mm
Depth	66 mm

Ambient conditions
Degree of protection	IP00
Degree of protection (Installation location)	≥ IP54 (Installation location)
Ambient temperature (operation)	-15 °C ... 50 °C
Ambient temperature (storage/transport)	-15 °C ... 50 °C
Altitude	≤ 2000 m

Air clearances and creepage distances, input/output
Standards/regulations	EN 61010-2-201
Air and creepage distances, output/output
Standards/regulations	EN 61010-2-201