UM-2KS50RM/32MR/SI/1/551/MT - Active module Phoenix Contact

Mã sản phẩm: 2968564

VARIOFACE output module, 32 channels for Yokogawa ADV 551, ADV 561 output modules.

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

General	Observe the maximum switching capacity of the relays used
General	Do not connect adjacent channels to SELV/ PELV and voltages dangerous to the touch.
General	The outputs are not suitable for switching different line conductors. The sum of the switching voltages used for adjacent outputs must not exceed the rated insulation voltage value
General	The necessary requirements for insulation (basic insulation or reinforced insulation) from adjacent modules (in DIN-rail direction) must be realized by applying suitable measures (e. g., partition plates).

Product type	Interface module
No. of channels	32
Operating mode	100% operating factor
Mechanical service life	approx. 2x 10⁷ cycles
Insulation characteristics
Insulation	Safe isolation, reinforced insulation
Insulation characteristics: Air clearances and creepage distances, input/output
Insulation	Safe isolation, reinforced insulation
Overvoltage category	III
Pollution degree	2
Insulation characteristics: Air and creepage distances, output/output
Insulation	Basic insulation
Overvoltage category	III
Pollution degree	2

No. of channels	32
Air clearances and creepage distances, input/output
Rated insulation voltage	300 V
Rated surge voltage	6 kV (1.2/50 μs)
Air and creepage distances, output/output
Rated insulation voltage	300 V
Rated surge voltage	4 kV (1.2/50 μs)
Supported controller YOKOGAWA CS3000 CentumVP
Suitable I/O card	ADV551
Suitable I/O card		ADV561
Supported controller YOKOGAWA STARDOM
Suitable I/O card	NFDV551
Suitable I/O card		NFDV561

Nominal input voltage U_N	24 V DC ±10 %
Input voltage range in reference to U_N	0.9 ... 1.1
Input voltage range	21.6 V DC ... 26.4 V DC
Typical input current at U_N	9 mA (K1 – K32)
Typical response time	5 ms (K1 – K32)
Typical response time		5 ms (K33)
Typical release time	7 ms (K1 – K32)
Typical release time		5 ms (K33)
Operating voltage display	Green LED
Status display/channel	Yellow LED

Switching
Contact type	1 changeover contact
Type of switch contact	Single contact
Contact material	AgSnO₂
Maximum switching voltage	250 V AC
Maximum switching voltage		63 V DC
Minimum switching voltage	12 V AC/DC
Limiting continuous current	2.8 A (observe derating)
Min. switching current	10 mA
Interrupting rating (ohmic load) max.	67 W (24 V DC)
		20 W (48 V DC)
		18 W (60 V DC)
		700 VA (250 V AC)
Output fuse	4 A (per channel)

Field level
Connection method	Screw connection with disconnect knife
Number of connections	1
Conductor cross section rigid	0.2 mm² ... 4 mm²
Conductor cross section flexible	0.2 mm² ... 2.5 mm²
Conductor cross section AWG	24 ... 12
Controller level
Connection method	Yokogawa KS-compatible
Number of connections	2
Number of positions	50
Note	Usable system cables: Phoenix Contact YUC50, Yokogawa AKB331
Tightening torque	0.5 Nm

Status display present

Yes

Ambient conditions
Degree of protection	IP00
Degree of protection (Installation location)	≥ IP54 (Installation location)
Ambient temperature (operation)	-15 °C ... 50 °C
Ambient temperature (storage/transport)	-20 °C ... 70 °C

Air clearances and creepage distances, input/output
Standards/regulations	EN 61010-2-201
Air and creepage distances, output/output
Standards/regulations	EN 61010-2-201