UM-2KS50/DO32REL/CS/SO180 - Active module Phoenix Contact

Mã sản phẩm: 2311373

32-channel relay module with a screw connection and redundant voltage supply. Suitable for Yokogawa ADV551 and ADV561 cards.

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

General	Observe the maximum switching capacity of the relays used
General	Do not connect adjacent channels to SELV/ PELV and voltages dangerous to the touch.
General	The outputs are not suitable for switching different line conductors. The sum of the switching voltages used for adjacent outputs must not exceed the rated insulation voltage value
General	The necessary requirements for insulation (basic insulation or reinforced insulation) from adjacent modules (in DIN-rail direction) must be realized by applying suitable measures (e. g., partition plates).

Product type	Interface module
No. of channels	32
Insulation characteristics
Insulation	Safe isolation, reinforced insulation
Insulation characteristics: Air clearances and creepage distances, input/output
Insulation	Safe isolation, reinforced insulation
Overvoltage category	III
Pollution degree	2
Insulation characteristics: Air and creepage distances, output/output
Insulation	Basic insulation
Overvoltage category	III
Pollution degree	2

No. of channels	32
Air clearances and creepage distances, input/output
Rated insulation voltage	300 V
Rated surge voltage	6 kV (1.2/50 μs)
Air and creepage distances, output/output
Rated insulation voltage	260 V
Rated surge voltage	4 kV (1.2/50 μs)
Supported controller YOKOGAWA CS3000 CentumVP
Suitable I/O card	ADV551
Suitable I/O card		ADV561
Supported controller YOKOGAWA STARDOM
Suitable I/O card	NFDV551
Suitable I/O card		NFDV561

Nominal input voltage U_N	24 V DC
Input voltage range in reference to U_N	0.9 ... 1.1
Input voltage range	21.6 V DC ... 26.4 V DC
Typical input current at U_N	9 mA (per relay)
Protective circuit	Damping diode, polarity protection; Damping diode, polarity protection diode
Status display/channel	Yellow LED

Switching
Contact type	1 N/O contact
Contact material	AgSnO, hard gold-plated
Maximum switching voltage	250 V AC
Limiting continuous current	50 mA
Min. switching current	10 mA
Interrupting rating (ohmic load) max.	1.2 W (at 24 V DC)
Switching: when the gold layer is destroyed
Note	the following values are applicable if a gold layer is destroyed
Maximum switching voltage	250 V AC/DC
Minimum switching voltage	5 V (at 100 mA)
Limiting continuous current	4 A (for 100% ED 2 A per channel)
Interrupting rating (ohmic load) max.	96 W (at 24 V DC)
		20 W (at 48 V DC)
		18 W (at 60 V DC)
		23 W (at 110 V DC)
		40 W (at 220 V DC)
		1000 VA (for 250 V AC)

Field level
Connection method	Screw connection
Number of positions	32
Conductor cross section rigid	0.14 mm² ... 1.5 mm²
Conductor cross section flexible	0.14 mm² ... 1.5 mm²
Conductor cross section AWG	26 ... 14
Controller level
Connection method	Yokogawa KS-compatible
Number of connections	1
Number of positions	50
Note	Usable system cables: Phoenix Contact YUC50, Yokogawa AKB331
Tightening torque	0.5 Nm
Power supply
Connection method	Screw connection
Number of positions	6
Conductor cross section rigid	0.2 mm² ... 2.5 mm²
Conductor cross section flexible	0.2 mm² ... 1.5 mm²
Conductor cross section AWG	26 ... 14

Status display present

Yes

Ambient conditions
Degree of protection	IP00
Ambient temperature (operation)	-20 °C ... 50 °C
Ambient temperature (storage/transport)	-20 °C ... 70 °C
Altitude	< 2000 m

Air clearances and creepage distances, input/output
Standards/regulations	EN 61010-2-201
Air and creepage distances, output/output
Standards/regulations	EN 61010-2-201