TRIO3-PS/1AC/24DC/10/4C/IOL - Power supply unit Phoenix Contact

Mã sản phẩm: 1252696

Danh mục: PHOENIX CONTACT, Supply, charge, and protect Phoenix Contact,

Primary-switched power supply unit, TRIO POWER, Push-in connection, 4-channel fuse module, IO-Link, DIN rail mounting, input: 1-phase, output: 24 V DC / 10 A

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

AC operation
Supply system configuration	Star network (TN, TT, IT (PE))
Nominal input voltage range	100 V AC ... 240 V AC
Input voltage range	100 V AC ... 240 V AC -15 % ... +10 %
Input voltage range		115 V AC ... 240 V AC ±10 % (UL)
Derating	< 100 V AC (1 %/V)
Derating		2.5 %/K, > 60 °C
Typical national grid voltage	120 V AC
Typical national grid voltage		230 V AC
Voltage type of supply voltage	AC
Inrush current	< 17 A (25 °C)
Inrush current integral (I²t)	< 0.5 A²s
Frequency range (f_N)	50 Hz ... 60 Hz ±10 %
Mains buffering time	typ. 27 ms (120 V AC)
Mains buffering time		typ. 28 ms (230 V AC)
Current consumption	2.6 A (100 V AC)
		2.2 A (120 V AC)
		1.2 A (230 V AC)
		1.1 A (240 V AC)
Protective circuit	Transient protection; Varistor
Power factor (cos phi)	0.95 (230 V AC)
Device mains fuse	6.3 A internal (device protection)
Recommended breaker for input protection	6 A ... 16 A (Characteristic B, C, D, K or comparable)
Discharge current to PE	< 3.5 mA
DC operation
Input voltage range	100 V DC ... 240 V DC ±10 %
Input voltage range		160 V DC ... 240 V DC ±10 % (UL)
Derating	< 140 V DC (1 %/V)
Voltage type of supply voltage	DC
Current consumption	2.7 A (100 V DC)
Current consumption		1.1 A (240 V DC)

Efficiency	typ. 94.5 % (120 V AC)
Efficiency		typ. 95.5 % (230 V AC)
Nominal output voltage	24 V DC
Setting range of the output voltage (U_Set)	24 V DC ... 28 V DC (> 24 V DC, constant capacity restricted)
Nominal output current (I_N)	10 A
Dynamic Boost (I_Dyn.Boost)	max. 15 A (5 s)
No. of channels	4
Nominal current per channel	1 A
		2 A
		3.8 A
		4 A
		6 A
		8 A
		10 A
Waiting time after switch off of a channel	5 s
Switch-on delay of the channels	100 ms
Short-circuit-proof	yes
Derating	60 °C ... 70 °C
Crest factor	typ. 1.75 (120 V AC)
Crest factor		typ. 1,7 (230 V AC)
Output power (P_N)	240 W
Output power (P_{Dyn. Boost})	max. 360 W (5 s)
Connection in parallel	no
Connection in series	No
Feedback voltage resistance	≤ 35 V DC
Protection against overvoltage at the output (OVP)	≤ 35 V DC
Residual ripple	typ. 50 mV_PP (with nominal values)
Control deviation	< 1 % (change in load, static 10 % ... 90 %)
		< 3 % (change in load, dynamic 10 % ... 90 %)
		< 0.1 % (change in input voltage ±10 %)
Rise time	≤ 1 s (U_Out = 10 % ... 90 %)
Minimum no-load power dissipation	< 1.2 W (120 V AC)
Maximum no-load power dissipation	< 1.3 W (230 V AC)
Minimum nominal load power dissipation	< 14.5 W (120 V AC)
Power loss nominal load max.	< 12 W (230 V AC)
Integrated fuse protection	yes
Signal relay 13/14
Position	3.x
Position marking	3.1 (13), 3.2 (14)
Switch contact (floating)	OptoMOS
Switching voltage	max. 30 V DC (SELV)
Current carrying capacity	max. 100 mA
State condition	U_Out > 21 V DC and I_Out < 0.9 x I_N (Contact closed)
State condition		U_Out < 21 V DC or I_Out > 0.9 x I_N (averaging over 60 s) (Contact open)

Input
Position	1.x
Conductor connection
Connection method	Push-in connection
rigid	0.2 mm² ... 4 mm²
rigid		1.5 mm² (recommended)
flexible	0.2 mm² ... 2.5 mm²
flexible		1.5 mm² (recommended)
flexible with ferrule without plastic sleeve	0.25 mm² ... 2.5 mm²
flexible with ferrule without plastic sleeve		1.5 mm² (recommended)
flexible with ferrule with plastic sleeve	0.25 mm² ... 1.5 mm²
flexible with ferrule with plastic sleeve		1.5 mm² (recommended)
rigid (AWG)	24 ... 12 (Cu)
rigid (AWG)		16 (recommended)
Stripping length	10 mm (rigid/flexible)
Stripping length		8 mm (Ferrule)
Output
Position	2.x
Conductor connection
Connection method	Push-in connection
rigid	0.2 mm² ... 4 mm²
rigid		1.5 mm² (recommended)
flexible	0.2 mm² ... 2.5 mm²
flexible		1.5 mm² (recommended)
flexible with ferrule without plastic sleeve	0.25 mm² ... 2.5 mm²
flexible with ferrule without plastic sleeve		1.5 mm² (recommended)
flexible with ferrule with plastic sleeve	0.25 mm² ... 1.5 mm²
flexible with ferrule with plastic sleeve		1.5 mm² (recommended)
rigid (AWG)	24 ... 12 (Cu)
rigid (AWG)		16 (recommended)
Stripping length	10 mm (rigid/flexible)
Stripping length		8 mm (Ferrule)
Output
Position	2.x
Conductor connection
Connection method	Push-in connection
rigid	0.2 mm² ... 4 mm²
rigid		1.5 mm² (recommended)
flexible	0.2 mm² ... 2.5 mm²
flexible		1.5 mm² (recommended)
flexible with ferrule without plastic sleeve	1.5 mm² (recommended)
flexible with ferrule with plastic sleeve	0.25 mm² ... 1.5 mm²
flexible with ferrule with plastic sleeve		1.5 mm² (recommended)
rigid (AWG)	24 ... 12 (Cu)
rigid (AWG)		16 (recommended)
Stripping length	10 mm (rigid/flexible)
Stripping length		8 mm (Ferrule)
Signal
Position	3.x
Conductor connection
Connection method	Push-in connection
rigid	0.2 mm² ... 1.5 mm²
rigid		0.5 mm² (recommended)
flexible	0.2 mm² ... 1.5 mm²
flexible		0.5 mm² (recommended)
flexible with ferrule without plastic sleeve	0.25 mm² ... 1.5 mm² (Cu)
flexible with ferrule without plastic sleeve		0.5 mm² (recommended)
flexible with ferrule with plastic sleeve	0.25 mm² ... 0.75 mm²
flexible with ferrule with plastic sleeve		0.5 mm² (recommended)
rigid (AWG)	24 ... 16 (Cu)
rigid (AWG)		20 (recommended)
Stripping length	10 mm (rigid/flexible)
Stripping length		8 mm (Ferrule)
Communication
Position	5.x
Conductor connection
Connection method	Push-in connection
rigid	0.2 mm² ... 1.5 mm²
rigid		0.5 mm² (recommended)
flexible	0.2 mm² ... 1.5 mm²
flexible		0.5 mm² (recommended)
flexible with ferrule without plastic sleeve	0.25 mm² ... 1.5 mm² (Cu)
flexible with ferrule without plastic sleeve		0.5 mm² (recommended)
flexible with ferrule with plastic sleeve	0.25 mm² ... 0.75 mm²
flexible with ferrule with plastic sleeve		0.5 mm² (recommended)
rigid (AWG)	24 ... 16 (Cu)
rigid (AWG)		20 (recommended)
Stripping length	10 mm (rigid/flexible)
Stripping length		8 mm (Ferrule)

IO-Link
Specification	V1.1
Interface	IO-Link
Number of interfaces	1
Connection method	Push-in connection
Position	5.x
Position marking	5.1 (L+), 5.2 (C/Q), 5.3 (L-)
Transmission physics	3-wire, standard industrial cable
Reverse polarity protection	yes
Transmission speed	230.4 kbps (COM3)
Cycle time	2 ms
Electrical isolation	yes
Amount of process data	6 Byte (Input data)
Device ID	262657_dec/ 0x040201_hex
Vendor ID	00B0_hex / 176_dez

Types of signaling	LED DC OK – signal state operation (U_N = 24 V DC, I_Out = I_N)
Function	Visual operating state display
Color	Yellow, green (bicolor LED)
LED off	Supply voltage input AC not present (Off)
LED on (green), DC OK	U_Out > 21 V DC and I_Out < 0.9 x I_N (On (green), DC OK)
LED on (yellow), IOut > 90%	U_Out > 21 V DC and I_Out > 0.9 x I_N (On (yellow), I_Out > 90% )
LED on (red), ISHORT	U_Out < 21 V DC and I_Out > 0.9 x I_N (On (red), I_SHORT)
LED on (flashing red) OVP	U_OUT > OVP (Over voltage protection) (On (flashing red))

Number of phases	1.00
Insulation voltage input/output	3 kV AC (type test)
Insulation voltage input/output		3 kV AC (routine test)

Product type	Power supply
Product family	TRIO POWER
MTBF (IEC 61709, SN 29500)	> 1300000 h (25 °C)
		> 860000 h (40 °C)
		> 400000 h (60 °C)
Environmental protection directive	RoHS Directive 2011/65/EU
		WEEE
		Reach
Insulation characteristics
Protection class	I
Degree of pollution	2

Dimensional drawing
Width	68 mm
Height	135 mm
Depth	132 mm
Depth Device depth (DIN rail mounting)	125 mm
Installation dimensions
Installation distance right/left (active)	15 mm / 15 mm
Installation distance right/left (passive)	0 mm / 0 mm (≤ 40 °C)

Mounting type	DIN rail mounting
Assembly instructions	alignable: 0 mm horizontally, 30 mm vertically
Mounting position	horizontal DIN rail NS 35, EN 60715
With protective coating	No

Flammability rating according to UL 94	V0 (Housing, terminal blocks)
Hood version	Polycarbonate
Side element version	Aluminum

Ambient conditions
Degree of protection	IP20
Ambient temperature (operation)	-25 °C ... 70 °C (> 60 °C Derating: 2,5 %/K)
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Ambient temperature (start-up type tested)	-40 °C
Maximum altitude	≤ 5000 m (> 2000 m, Derating: 10 %/1000 m)
Max. permissible relative humidity (operation)	≤ 95 % (at 25 °C, non-condensing)
Shock (operation)	18 ms, 30g, per spatial direction (IEC 60068-2-27)
Vibration (operation)	10 Hz ... 50 Hz, amplitude ±0.2 mm (IEC 60068-2-6)
Vibration (operation)		50 Hz to 150 Hz, 2.3 g, 90 min.

Overvoltage category
EN 61010-1	III (≤ 2000 m)
		II (≤ 5000 m)
Overvoltage category
EN 61010-2-201	III (≤ 2000 m)
		II (≤ 5000 m)
Safety of power supply units up to 1100 V (insulation distances)
Standards/specifications	DIN EN 61558-2-16
Electrical safety
Standards/specifications	IEC 61010-2-201 (SELV)
Electronic equipment for use in power installations
Standards/specifications	EN 50178/VDE 0160 (PELV)
Safety for measurement, control, and laboratory equipment
Standards/specifications	IEC 61010-1
Protective extra-low voltage
Standards/specifications	IEC 61010-1 (SELV)
		IEC 61010-2-201 (PELV)
Safe isolation
Standards/specifications	IEC 61558-2-16
		IEC 61010-2-201
Limitation of harmonic line currents
Standards/specifications	EN 61000-3-2

UL
Identification	UL/C-UL Listed UL 61010-1
UL
Identification	UL/C-UL Listed UL 61010-2-201
ANSI/UL
Identification	PROCESS CONTROL EQUIPEMENT FOR HAZARDOUS LOCATIONS
		(EN)  This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D, Hazardous Locations, or non-hazardous locations only. (FR)  Cet appareil convient uniquement pour une utilisation en atmosphères explosibles de classe I, division 2, groupes A, B, C et D ou en atmosphères non explosibles.
		(EN)  WARNING: Explosion Hazard - Do not connect or disconnect equipment unless power has been switched off or the area is known to be non-hazardous. (FR)  AVERTISSEMENT : risque d'explosion - ne pas connecter ou déconnecter les équipements sauf si l'alimentation a été coupée ou si la zone est réputée non dangereuse.
		(EN)  If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired. (FR)  Si l'équipement est utilisé d'une manière non spécifiée par le fabricant, la protection fournie par cet équipement peut être altérée.
		(EN)  This equipement must be installed in a suitable, tool secured/key locked enclosure. (FR)  Cet équipement doit être installé dans un boîtier approprié, verrouillé par une clé ou dont l'ouverture nécessite l'utilisation d'un outil.

Low Voltage Directive	Conformance with Low Voltage Directive 2014/35/EC
Interference emission	Interference emission in accordance with EN 61000-6-3 (residential and commercial) and EN 61000-6-4 (industrial)
Noise immunity	Immunity in accordance with EN 61000-6-1 (residential), EN 61000-6-2 (industrial)
Electromagnetic compatibility	Conformance with EMC Directive 2014/30/EU
Conducted noise emission	EN 55016
Conducted noise emission		EN 61000-6-3 (Class B)
Noise emission	EN 55016
Noise emission		EN 61000-6-3 (Class B)
DNV GL conducted interference	Class A
Additional text	Area power distribution
DNV GL noise radiation	Class B
Additional text	Bridge and deck area
Harmonic currents
Standards/regulations	EN 61000-3-2
Standards/regulations		EN 61000-3-2 (Class A)
Frequency range	0 kHz ... 2 kHz
Flicker
Standards/regulations	EN 61000-3-3
Standards/regulations		EN 61000-3-3
Frequency range	0 kHz ... 2 kHz
Electrostatic discharge
Standards/regulations	EN 61000-4-2
Electrostatic discharge
Contact discharge	6 kV (Test Level 3)
Discharge in air	8 kV (Test Level 3)
Comments	Criterion B
Electromagnetic HF field
Standards/regulations	EN 61000-4-3
Electromagnetic HF field
Frequency range	80 MHz ... 1 GHz
Test field strength	10 V/m (Test Level 3)
Frequency range	1 GHz ... 6 GHz
Test field strength	10 V/m (Test Level 3)
Comments	Criterion A
Fast transients (burst)
Standards/regulations	EN 61000-4-4
Fast transients (burst)
Input	asymmetrical 2 kV (Test Level 3)
Output	asymmetrical 2 kV (Test Level 4)
Signal	asymmetrical 1 kV (Test Level 3)
Comments	Criterion A
Surge voltage load (surge)
Standards/regulations	EN 61000-4-5
Input	symmetrical 4 kV (Test Level 4)
Input		asymmetrical 2 kV (Test Level 4)
Output	symmetrical 1 kV (Test Level 3)
Output		asymmetrical 2 kV (Test Level 3)
Signal	asymmetrical 1 kV (Test Level 2)
Comments	Criterion A
Conducted interference
Standards/regulations	EN 61000-4-6
Conducted interference
I/O/S	asymmetrical
Frequency range	0.15 MHz ... 80 MHz
Comments	Criterion A
Voltage	10 V (Test Level 3)
Voltage dips
Standards/regulations	EN 61000-4-11
Voltage	230 V AC
Frequency	50 Hz
Voltage dip	70 %
Number of periods	25 periods
Additional text	Class 3
Comments	Criterion A
Voltage dip	40 %
Number of periods	10 periods
Additional text	Class 3
Comments	Criterion B
Voltage dip	0 %
Number of periods	1 period
Additional text	Class 3
Comments	Criterion A
Criteria
Criterion A	Normal operating behavior within the specified limits.
Criterion B	Temporary impairment to operational behavior that is corrected by the device itself.
Criterion C	Temporary adverse effects on the operating behavior, which the device corrects automatically or which can be restored by actuating the operating elements.