TRIO-PS-2G/3AC/72DC/14 - Power supply unit Phoenix Contact

Mã sản phẩm: 1076188

Danh mục: PHOENIX CONTACT, Supply, charge, and protect Phoenix Contact,

Primary-switched TRIO power supply for DIN rail mounting, input: 3-phase, output: 72 V DC/14 A, dynamic boost, tool-free fast connection technology for rigid and flexible conductors with ferrule

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

AC operation
Network type	Star network
Nominal input voltage range	3x 400 V AC ... 500 V AC
Input voltage range	3x 400 V AC ... 500 V AC -20 % ... +15 %
Typical national grid voltage	3x 400 V AC
Typical national grid voltage		3x 480 V AC
Voltage type of supply voltage	AC
Inrush current	≤ 30 A (typical)
Inrush current integral (I²t)	< 1.1 A²s
Inrush current limitation	35 A (after 1 ms)
AC frequency range	50 Hz ... 60 Hz
Frequency range (f_N)	50 Hz ... 60 Hz ±5 Hz
Mains buffering time	> 10 ms (400 V AC)
Mains buffering time		> 20 ms (480 V AC)
Current consumption	3x 1.9 A (400 V AC)
Current consumption		3x 1.7 A (500 V AC)
Nominal power consumption	1335.1 VA
Protective circuit	Transient surge protection; Varistor
Power factor (cos phi)	0.77
Typical response time	< 1 s
Input fuse	6.3 A (internal (device protection))
Recommended breaker for input protection	10 A ... 16 A (Characteristics B, C, D, K)
Discharge current to PE	< 3.5 mA
Discharge current to PE		< 2.5 mA (550 V AC, 60 Hz)

Efficiency	> 94.6 % (400 V AC)
Efficiency		> 94.3 % (480 V AC)
Output characteristic	U/I with dynamic load reserve
Nominal output voltage	72 V DC ±1 %
Setting range of the output voltage (U_Set)	70 V DC ... 85 V DC (> 72 V DC, constant capacity restricted)
Nominal output current (I_N)	14 A
Dynamic Boost (I_Dyn.Boost)	21 A (5 s)
Derating	> 60 °C ... 70 °C (2.5%/K)
Feedback voltage resistance	< 105 V DC
Protection against overvoltage at the output (OVP)	≤ 105 V DC
Control deviation	< 1 % (change in load, static 10 % ... 90 %)
		< 3 % (Dynamic load change 10 % ... 90 %, 10 Hz)
		< 0.1 % (change in input voltage ±10 %)
Residual ripple	≤ 300 mV_PP
Short-circuit-proof	yes
No-load proof	yes
Output power	1008 W
Output power		1512 W
Maximum no-load power dissipation	< 7 W (400 V AC)
Power loss nominal load max.	< 58 W (400 V AC)
Short-circuit current	< 23.5 A DC (Permanent)
Rise time	≤ 2 ms (U_OUT (10 % ... 90 %))
Connection in parallel	yes
Connection in series	yes
Signal: DC OK
Continuous load current	100 mA
Signal relay 13/14
Default	closed
Digital	30 V AC 30 V DC 100 mA

Input
Connection method	Push-in connection
Conductor cross section, rigid min.	0.2 mm²
Conductor cross section, rigid max.	4 mm²
Conductor cross section flexible min.	0.2 mm²
Conductor cross section flexible max.	4 mm²
Single conductor/flexible terminal point with ferrule with plastic sleeve, min.	0.2 mm²
Single conductor/flexible terminal point with ferrule with plastic sleeve, max.	2.5 mm²
Single conductor/flexible terminal point with ferrule without plastic sleeve, min.	0.2 mm²
Single conductor/flexible terminal point with ferrule without plastic sleeve, max.	2.5 mm²
Conductor cross section AWG min.	24
Conductor cross section AWG max.	12
Stripping length	10 mm
Output
Connection method	Push-in connection
Conductor cross section, rigid min.	0.75 mm²
Conductor cross section, rigid max.	16 mm²
Conductor cross section flexible min.	0.75 mm²
Conductor cross section flexible max.	16 mm²
Single conductor/flexible terminal point with ferrule with plastic sleeve, min.	0.75 mm²
Single conductor/flexible terminal point with ferrule with plastic sleeve, max.	10 mm²
Single conductor/flexible terminal point with ferrule without plastic sleeve, min.	0.75 mm²
Single conductor/flexible terminal point with ferrule without plastic sleeve, max.	16 mm²
Conductor cross section AWG min.	20
Conductor cross section AWG max.	4
Stripping length	18 mm
Signal
Connection method	Push-in connection
Conductor cross section, rigid min.	0.2 mm²
Conductor cross section, rigid max.	0.75 mm²
Conductor cross section flexible min.	0.2 mm²
Conductor cross section flexible max.	1.5 mm²
Single conductor/flexible terminal point with ferrule with plastic sleeve, min.	0.2 mm²
Single conductor/flexible terminal point with ferrule with plastic sleeve, max.	0.75 mm²
Single conductor/flexible terminal point with ferrule without plastic sleeve, min.	0.2 mm²
Single conductor/flexible terminal point with ferrule without plastic sleeve, max.	1 mm²
Conductor cross section AWG min.	24
Conductor cross section AWG max.	18
Stripping length	8 mm

Types of signaling	LED
Types of signaling		Floating signal contact
Signal output: LED status indicator
Signalization designation	DC OK
Status display	LED
Color	green
DC OK	U_OUT > 0.95 x U_N (U_N = 72 V DC)

Number of phases	3.00
Insulation voltage input/output	3 kV AC (type test)
Insulation voltage input/output		1.5 kV AC (routine test)

Product type	Power supply
Product family	TRIO POWER
MTBF (IEC 61709, SN 29500)	> 1730000 h (25 °C)
		> 1051000 h (40 °C)
		> 510000 h (60 °C)
Insulation characteristics
Protection class	I (in closed control cabinet)
Degree of pollution	2

Width	110 mm
Height	130 mm
Depth	160 mm
Installation dimensions
Installation distance right/left	0 mm / 0 mm
Installation distance top/bottom	50 mm / 50 mm

Mounting type	DIN rail mounting
Assembly instructions	alignable: horizontally 0 mm (≤ 40 °C) 10 mm (≤ 70 °C), vertically 50 mm
Mounting position	horizontal DIN rail NS 35, EN 60715
With protective coating	No

Flammability rating according to UL 94 (housing / terminal blocks)	V0
Housing material	Plastic
Type of housing	Aluminum (AlMg3)
Hood version	Polycarbonate

Ambient conditions
Degree of protection	IP20
Ambient temperature (operation)	-25 °C ... 70 °C (> 60 °C Derating: 2,5 %/K)
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Ambient temperature (start-up type tested)	-40 °C
Maximum altitude	≤ 4000 m (> 2000 m, Derating: 10 %/1000 m)
Climatic class	3K3 (in acc. with EN 60721)
Max. permissible relative humidity (operation)	≤ 95 % (at 25 °C, non-condensing)
Shock	11 ms, 15 g, in each space direction (according to IEC 60068-2-27)
Vibration (operation)	< 15 Hz, amplitude ±2.5 mm (according to IEC 60068-2-6)
Vibration (operation)		15 Hz ... 150 Hz, 0.7g, 90 min.

Standard – Limitation of mains harmonic currents	EN 61000-3-2
Standard - Electrical safety	IEC 61010-2-201
Standard - Safe isolation	DIN VDE 0100-410
Standard - Safety of transformers	EN 61558-2-16 (air clearances and creepage distances only)
Overvoltage category
EN 61010-1	II (≤ 2000 m)

UL approvals	UL/C-UL Listed UL 61010-1
Conformity/Approvals
SIL in accordance with IEC 61508	0

Low Voltage Directive	Conformance with Low Voltage Directive 2014/35/EC
Interference emission	Interference emission in accordance with EN 61000-6-3 (residential and commercial) and EN 61000-6-4 (industrial)
EMC requirements for noise immunity	EN 61000-6-1
EMC requirements for noise immunity		EN 61000-6-2
Electromagnetic compatibility	Conformance with EMC Directive 2014/30/EU
Conducted noise emission	EN 55016-2-1
Conducted noise emission		EN 61000-6-4 (Class A)
Noise emission	EN 55011 (EN 55022)
Noise emission	EN 55016-2-3
Noise emission		EN 61000-6-4 (Class A)
Harmonic currents
Standards/regulations	EN 55016-2-3
Standards/regulations		EN 61000-3-2 (Class A)
Flicker
Standards/regulations	EN 61000-3-3
Standards/regulations		EN 61000-3-3
Electrostatic discharge
Standards/regulations	EN 61000-4-2
Electrostatic discharge
Contact discharge	6 kV (Test Level 3)
Discharge in air	8 kV (Test Level 3)
Comments	Criterion A
Electromagnetic HF field
Standards/regulations	EN 61000-4-3
Electromagnetic HF field
Frequency range	80 MHz ... 1 GHz
Test field strength	10 V/m (Test Level 3)
Frequency range	1 GHz ... 2 GHz
Test field strength	10 V/m (Test Level 3)
Frequency range	2 GHz ... 6 GHz
Test field strength	10 V/m (Test Level 3)
Comments	Criterion A
Fast transients (burst)
Standards/regulations	EN 61000-4-4
Fast transients (burst)
Input	4 kV (Test Level 3 - asymmetrical)
Output	2 kV (Test Level 3 - asymmetrical)
Signal	2 kV (Test Level 3 - asymmetrical)
Comments	Criterion A
Surge voltage load (surge)
Standards/regulations	EN 61000-4-5
Input	2 kV (Test Level 4 - symmetrical)
Input		4 kV (Test Level 4 - asymmetrical)
Output	1 kV (Test Level 3 - symmetrical)
Output		2 kV (Test Level 3 - asymmetrical)
Signal	1 kV (Test Level 2 - asymmetrical)
Comments	Criterion A
Conducted interference
Standards/regulations	EN 61000-4-6
Conducted interference
Input/Output	asymmetrical
Frequency range	0.15 MHz ... 80 MHz
Comments	Criterion A
Voltage	10 V (Test Level 3)
Voltage dips
Standards/regulations	EN 61000-4-11
Voltage	400 V AC
Frequency	50 Hz
Voltage dip	70 %
Number of periods	25 periods
Comments	Criterion A
Voltage dip	40 %
Number of periods	10 periods
Comments	Criterion A
Voltage dip	0 %
Number of periods	1 period
Comments	Criterion A
Emitted interference
Standards/regulations	EN 61000-6-3
Radio interference voltage in acc. with EN 55011	EN 55011 (EN 55022) Class B, area of application: Industry and residential
Emitted radio interference in acc. with EN 55011	EN 55011 (EN 55022) Class B, area of application: Industry and residential
Criteria
Criterion A	Normal operating behavior within the specified limits.
Criterion B	Temporary impairment to operational behavior that is corrected by the device itself.
Criterion C	Temporary adverse effects on the operating behavior, which the device corrects automatically or which can be restored by actuating the operating elements.