STEP3-PS/1AC/24DC/3.75/PT/LED - Power supply unit Phoenix Contact

Mã sản phẩm: 1285036

Danh mục: PHOENIX CONTACT, Supply, charge, and protect Phoenix Contact,

Primary-switched LED power supply, STEP POWER, Push-in connection, DIN rail or direct mounting, input: 1-phase, output: 24 V DC / 3.75 A

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

AC operation
Network type	Star network
Input voltage range	100 V AC ... 240 V AC -15 % ... +10 %
Derating	< 100 V AC ... 85 V AC (1 %/V)
Typical national grid voltage	120 V AC
Typical national grid voltage		230 V AC
Voltage type of supply voltage	AC/DC
Inrush current	typ. 30 A (25 °C)
Inrush current integral (I²t)	typ. 0.35 A²s
Frequency range (f_N)	50 Hz ... 60 Hz ±10 %
Mains buffering time	typ. 25 ms (120 V AC)
Mains buffering time		typ. 25 ms (230 V AC)
Current consumption	1 A (100 V AC)
Current consumption		0.45 A (240 V AC)
Protective circuit	Transient surge protection; Varistor
Switch-on time	typ. 2 s
Device mains fuse	4 A internal (device protection), slow-blow
Recommended breaker for input protection	6 A ... 16 A (Characteristics B, C, D, K)
Discharge current to PE	< 0.25 mA
DC operation
Input voltage range	110 V DC ... 250 V DC -20 % ... +10 %
Derating	< 110 V DC ... 88 V DC (1 %/V)
Current consumption	0.88 A (110 V DC)
Current consumption		0.38 A (250 V DC)

Efficiency	> 92.5 % (120 V AC)
Efficiency		> 94 % (230 V AC)
Nominal output voltage	24 V DC
Nominal output current (I_N)	3.75 A
Short-circuit-proof	yes
No-load proof	yes
Derating	> 50 °C ... 70 °C (2 % / K)
Crest factor	typ. 1.78
Crest factor		typ. 1.87
Output power (P_N)	90 W
Connection in parallel	yes, for increasing power and redundancy with diode
Connection in series	yes, for increased output voltage
Feedback voltage resistance	≤ 35 V DC
Protection against overvoltage at the output (OVP)	< 35 V DC
Residual ripple	typ. 100 mV_PP
Control deviation	< 0.5 % (Static load change 10 % ... 90 %)
		< 3 % (Dynamic load change 10 % ... 90 %, (10 Hz))
		< 0.1 % (change in input voltage ±10 %)
Rise time	typ. 100 ms (U_Out = 10 % ... 90 %)
Minimum no-load power dissipation	< 0.21 W (120 V AC)
Maximum no-load power dissipation	< 0.21 W (230 V AC)
Minimum nominal load power dissipation	< 7 W (120 V AC)
Power loss nominal load max.	< 5.7 W (230 V AC)

Input
Position	1.x
Conductor connection
Connection method	Push-in connection
rigid	0.2 mm² ... 2.5 mm²
rigid		1 mm² (recommended)
flexible	0.2 mm² ... 2.5 mm²
flexible		1 mm² (recommended)
flexible with ferrule without plastic sleeve	0.5 mm² ... 1.5 mm²
flexible with ferrule without plastic sleeve		1 mm² (recommended)
flexible with ferrule with plastic sleeve	0.2 mm² ... 1 mm²
flexible with ferrule with plastic sleeve		1 mm² (recommended)
rigid (AWG)	24 ... 14 (Cu)
rigid (AWG)		17 (recommended)
Stripping length	10 mm (rigid/flexible)
Stripping length		10 mm (Ferrule)
Output
Position	2.x
Conductor connection
Connection method	Push-in connection
rigid	0.2 mm² ... 2.5 mm²
rigid		1 mm² (recommended)
flexible	0.2 mm² ... 2.5 mm²
flexible		1 mm² (recommended)
flexible with ferrule without plastic sleeve	0.5 mm² ... 1.5 mm²
flexible with ferrule without plastic sleeve		1 mm² (recommended)
flexible with ferrule with plastic sleeve	0.2 mm² ... 1 mm²
flexible with ferrule with plastic sleeve		1 mm² (recommended)
rigid (AWG)	24 ... 14 (Cu)
rigid (AWG)		17 (recommended)
Stripping length	10 mm (rigid/flexible)
Stripping length		10 mm (Ferrule)

Types of signaling	LED DC OK – signal state operation (U_N = 24 V DC, I_Out = I_N)
Function	Visual operating state display
Color	green
LED off	Supply voltage input AC not present (Off)
LED on (green), DC OK	U_Out >0.9 x U_N(U_N = 24 V DC) (on)
Signal threshold	> 0,9 x U_N(U_N = 24 V DC) (LED lights up green)
Signal threshold		< 0,9 x U_N(U_N = 24 V DC) (LED off)

Number of phases	1.00
Insulation voltage input/output	4 kV AC (type test)
Insulation voltage input/output		3.75 kV AC (routine test)

Product type	Power supply
Product family	STEP POWER
MTBF (IEC 61709, SN 29500)	> 2036000 h (25 °C)
		> 1175000 h (40 °C)
		> 777000 h (50 °C)
Environmental protection directive	RoHS Directive 2011/65/EU
		WEEE
		Reach
Insulation characteristics
Protection class	II (in closed control cabinet)
Degree of pollution	2

Dimensional drawing
Width	72 mm
Height	90 mm
Depth	43 mm
Depth Device depth (DIN rail mounting)	37 mm (Device depth (DIN rail mounting))
Horizontal pitch	4 Div. (DIN 43880)
Installation dimensions
Installation distance right/left	0 mm / 0 mm
Installation distance top/bottom	30 mm / 30 mm

Mounting type	DIN rail or direct mounting
Assembly instructions	alignable: 0 mm horizontally, 30 mm vertically
Mounting position	horizontal DIN rail NS 35, EN 60715
With protective coating	No

Flammability rating according to UL 94	V0 (Housing, terminal blocks, base latches)
Housing material	Plastic
Foot latch material	Polyamid
Housing material	Polycarbonate

Ambient conditions
Degree of protection	IP20
Ambient temperature (operation)	-10 °C ... 50 °C
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Ambient temperature (start-up type tested)	-25 °C
Maximum altitude	≤ 2000 m
Max. permissible relative humidity (operation)	≤ 95 % (non-condensing)
Shock (operation)	18 ms, 30g, per spatial direction (IEC 60068-2-27)
Vibration (operation)	< 15 Hz, amplitude ±2.5 mm (IEC 60068-2-6)
Vibration (operation)		15 Hz ... 150 Hz, 2.3g, 90 min.

Overvoltage category
EN 61347-1	II (≤ 2000 m)
Overvoltage category
EN 62477-1	III (≤ 2000 m)
Electrical safety
Standards/specifications	IEC 61010-1 (SELV)
Protective extra-low voltage
Standards/specifications	IEC 61010-1 (SELV)
		IEC 61010-2-201 (PELV)
Requirements for electronic operating devices for LED modules
Standards/specifications	IEC 61347-2-13
Safe isolation
Standards/specifications	IEC 61558-2-16
EMC requirements for electrical lighting equipment
Standards/specifications	EN 55015
Low-voltage power supplies, DC output
Standards/specifications	EN 61204-3
Safety requirements for electrical equipment for measurement, control, and laboratory use
Standards/specifications	IEC 61010-1
Household and similar electrical appliances - Safety
Standards/specifications	DIN EN 60335-1
Equipment for general lighting purposes – EMC immunity requirements
Standards/specifications	EN 61547
Electric vehicle conductive charging system - Part 21-2: EMC requirements for off board electric vehicle charging systems
Standards/specifications	IEC 61851-21-2

UL
Identification	UL 1310 Class 2 Power Units
UL
Identification	UL/C-UL Listed UL 61010-1
UL
Identification	UL/C-UL Listed UL 61010-2-201
UL
Identification	UL/C-UL Listed ANSI/UL 121201 Class I, Division 2, Groups A, B, C, D (Hazardous Location)

Low Voltage Directive	Conformance with Low Voltage Directive 2014/35/EC
Interference emission	Interference emission in accordance with EN 61000-6-3 (residential and commercial) and EN 61000-6-4 (industrial)
Noise immunity	EN 61000-6-2:2005
Electromagnetic compatibility	Conformance with EMC Directive 2014/30/EU
Conducted noise emission	EN 55016
Conducted noise emission		EN 61000-6-3 (Class B)
Noise emission	EN 55016
Noise emission		EN 61000-6-3 (Class B)
Harmonic currents
Standards/regulations	EN 61000-3-2
Standards/regulations		EN 61000-3-2 (Class C)
Flicker
Standards/regulations	EN 61000-3-3
Frequency range	0 kHz ... 2 kHz
Electrostatic discharge
Standards/regulations	EN 61000-4-2
Electrostatic discharge
Contact discharge	6 kV (Test Level 3)
Discharge in air	8 kV (Test Level 3)
Comments	Criterion A
Electromagnetic HF field
Standards/regulations	EN 61000-4-3
Electromagnetic HF field
Frequency range	80 MHz ... 1 GHz
Test field strength	10 V/m (Test Level 3)
Frequency range	1 GHz ... 6 GHz
Test field strength	10 V/m (Test Level 3)
Comments	Criterion A
Fast transients (burst)
Standards/regulations	EN 61000-4-4
Fast transients (burst)
Input	asymmetrical 4 kV (Test Level 4)
Output	asymmetrical 2 kV (Test Level 3)
Comments	Criterion A
Surge voltage load (surge)
Standards/regulations	EN 61000-4-5
Input	symmetrical 2 kV (Test Level 4)
Input		asymmetrical 4 kV (Test Level 4)
Output	symmetrical 1 kV (Test Level 3)
Output		asymmetrical 2 kV (Test Level 3)
Comments	Criterion B
Conducted interference
Standards/regulations	EN 61000-4-6
Conducted interference
Input/Output	asymmetrical
Frequency range	0.15 MHz ... 80 MHz
Comments	Criterion A
Voltage	10 V (Test Level 3)
Voltage dips
Standards/regulations	EN 61000-4-11
Voltage	230 V AC
Frequency	50 Hz
Voltage dip	70 %
Number of periods	25 periods
Additional text	Class 3
Comments	Criterion A
Voltage dip	40 %
Number of periods	10 periods
Additional text	Class 3
Comments	Criterion A
Voltage dip	0 %
Number of periods	1 period
Additional text	Class 3
Comments	Criterion A
Criteria
Criterion A	Normal operating behavior within the specified limits.
Criterion B	Temporary impairment to operational behavior that is corrected by the device itself.
Criterion C	Temporary adverse effects on the operating behavior, which the device corrects automatically or which can be restored by actuating the operating elements.