QUINT4-PS/1AC/24DC/3.8/SC - Power supply unit Phoenix Contact

Mã sản phẩm: 2904599

Danh mục: PHOENIX CONTACT, Supply, charge, and protect Phoenix Contact,

Primary-switched power supply unit QUINT POWER, Screw connection, DIN rail mounting, input: 1-phase, output: 24 V DC / 3.8 A

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

AC operation
Input voltage range	100 V AC ... 240 V AC -15 % ... +10 %
Electric strength, max.	300 V AC 30 s
Typical national grid voltage	120 V AC
Typical national grid voltage		230 V AC
Voltage type of supply voltage	AC/DC
Inrush current	typ. 13 A (at 25 °C)
Inrush current integral (I²t)	< 0.18 A²s
Inrush current limitation	6.4 A (after 1 ms)
Inrush current limitation		< 13 A
Frequency range (f_N)	50 Hz ... 60 Hz -10 % ... +10 %
Mains buffering time	typ. 35 ms (120 V AC)
Mains buffering time		typ. 35 ms (230 V AC)
Current consumption	1 A (100 V AC)
		0.83 A (120 V AC)
		0.46 A (230 V AC)
		0.44 A (240 V AC)
Nominal power consumption	104 VA
Protective circuit	Transient surge protection; Varistor
Typical response time	500 ms
Input fuse	3.15 A (slow-blow, internal)
Recommended breaker for input protection	6 A ... 16 A (Characteristic B, C or comparable)
Discharge current to PE	< 0.25 mA (264 V AC, 60 Hz)
Discharge current to PE		0.18 mA (264 V AC, 60 Hz)
DC operation
Input voltage range	110 V DC ... 250 V DC -20 % ... +40 %
Voltage type of supply voltage	AC/DC
Current consumption	0.91 A (110 V DC)
Current consumption		0.4 A (250 V DC)

Efficiency	typ. 92.8 % (120 V AC)
Efficiency		typ. 93.7 % (230 V AC)
Output characteristic	U/I Advanced
Nominal output voltage	24 V DC
Setting range of the output voltage (U_Set)	24 V DC ... 28 V DC (constant capacity)
Nominal output current (I_N)	3.8 A
Dynamic Boost (I_Dyn.Boost)	7 A (≤ 60 °C (5 s))
Derating	> 60 °C (2.5%/K)
Feedback voltage resistance	≤ 35 V DC
Protection against overvoltage at the output (OVP)	≤ 32 V DC
Control deviation	< 0.5 % (Static load change 10 % ... 90 %)
		< 3 % (Dynamic load change 10 % ... 90 %, (10 Hz))
		< 0.2 % (change in input voltage ±10 %)
Residual ripple	< 45 mV_PP (with nominal values)
Short-circuit-proof	yes
No-load proof	yes
Output power	90 W
Output power		170 W
Maximum no-load power dissipation	< 1 W (120 V AC)
Maximum no-load power dissipation		< 1 W (230 V AC)
Power loss nominal load max.	< 7 W (120 V AC)
Power loss nominal load max.		< 6 W (230 V AC)
Crest factor	typ. 1.57 (120 V AC)
Crest factor		typ. 1,7 (230 V AC)
Rise time	50 ms (U_Out = 10 % ... 90 %)
Connection in parallel	yes, for redundancy and increased capacity
Connection in series	yes
Signal (configurable)
Digital	0 V DC 24 V DC 30 mA
Default	24 V DC 30 mA 24 V DC for U_Out > 0.9 x U_Set

Input
Connection method	Screw connection
Conductor cross section, rigid min.	0.14 mm²
Conductor cross section, rigid max.	2.5 mm²
Conductor cross section flexible min.	0.14 mm²
Conductor cross section flexible max.	2.5 mm²
Single conductor/terminal point, stranded, with ferrule, min.	0.25 mm²
Single conductor/terminal point, stranded, with ferrule, max.	2.5 mm²
Conductor cross section AWG min.	26
Conductor cross section AWG max.	14
Stripping length	8 mm
Tightening torque, min	0.5 Nm
Tightening torque max	0.6 Nm
Output
Connection method	Screw connection
Conductor cross section, rigid min.	0.14 mm²
Conductor cross section, rigid max.	2.5 mm²
Conductor cross section flexible min.	0.14 mm²
Conductor cross section flexible max.	2.5 mm²
Single conductor/terminal point, stranded, with ferrule, min.	0.25 mm²
Single conductor/terminal point, stranded, with ferrule, max.	2.5 mm²
Conductor cross section AWG min.	26
Conductor cross section AWG max.	14
Stripping length	8 mm
Tightening torque, min	0.5 Nm
Tightening torque max	0.6 Nm
Signal
Connection method	Screw connection
Conductor cross section, rigid min.	0.14 mm²
Conductor cross section, rigid max.	2.5 mm²
Conductor cross section flexible min.	0.14 mm²
Conductor cross section flexible max.	2.5 mm²
Single conductor/terminal point, stranded, with ferrule, min.	0.25 mm²
Single conductor/terminal point, stranded, with ferrule, max.	2.5 mm²
Conductor cross section AWG min.	26
Conductor cross section AWG max.	14
Stripping length	8 mm
Tightening torque, min	0.5 Nm
Tightening torque max	0.6 Nm

Types of signaling	LED
Signal output
P_Out	> P_Thr (LED lights up yellow, output power > P_Thr, depending on the rotary selector switch setting)
U_Out	> 0.9 x U_Set (LED lights up green)
U_Out		< 0.9 x U_Set (LED flashes green)

Number of phases	1.00
Insulation voltage input/output	4 kV AC (type test)
Insulation voltage input/output		3 kV AC (routine test)
Switching frequency	5 kHz ... 65 kHz (Auxiliary converter stage)
		30 kHz ... 150 kHz (PFC stage)
		80 kHz ... 150 kHz (Main converter stage)

Product type	Power supply
Product family	QUINT POWER
MTBF (IEC 61709, SN 29500)	> 1272000 h (25 °C)
		> 690000 h (40 °C)
		> 271000 h (60 °C)
Environmental protection directive	RoHS Directive 2011/65/EU
		WEEE
		Reach
Insulation characteristics
Protection class	II
Degree of pollution	2
Life expectancy (electrolytic capacitors)
Current	3.8 A
Temperature	40 °C
Time	57000 h
Additional text	120 V AC
Life expectancy (electrolytic capacitors)
Current	3.8 A
Temperature	40 °C
Time	61000 h
Additional text	230 V AC
Life expectancy (electrolytic capacitors)
Current	3.8 A
Temperature	25 °C
Time	162000 h
Additional text	120 V AC
Life expectancy (electrolytic capacitors)
Current	3.8 A
Temperature	25 °C
Time	173000 h
Additional text	230 V AC

Dimensional drawing
Width	45 mm
Height	99 mm
Depth	90 mm
Installation dimensions
Installation distance right/left (active)	15 mm / 15 mm (P_Out ≥50% )
Installation distance right/left (passive)	5 mm / 5 mm (P_Out ≥50% )
Installation distance top/bottom (active)	30 mm / 30 mm (P_Out ≥50% )
Installation distance top/bottom (passive)	30 mm / 30 mm (P_Out ≥50% )
Installation distance top/bottom (active, passive)	30 mm / 30 mm (P_Out ≤50 %)

Mounting type	DIN rail mounting
Assembly instructions	DIN rail mounting
With protective coating	No

Flammability rating according to UL 94 (housing / terminal blocks)	V0
Housing material	Plastic
Type of housing	Polycarbonate
Hood version	Polycarbonate

Ambient conditions
Degree of protection	IP20
Ambient temperature (operation)	-25 °C ... 70 °C (> 60 °C Derating: 2,5 %/K)
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Ambient temperature (start-up type tested)	-40 °C
Maximum altitude	≤ 5000 m (> 2000 m, observe derating)
Climatic class	3K3 (in acc. with EN 60721)
Max. permissible relative humidity (operation)	≤ 95 % (at 25 °C, non-condensing)
Shock	18 ms, 30g, in each space direction (according to IEC 60068-2-27)
Vibration (operation)	< 15 Hz, ±2.5 mm amplitude; 15 Hz ... 100 Hz: 2.3 g 90 Min. (in accordance with IEC 60068-2-6)

Standard – Limitation of mains harmonic currents	EN 61000-3-2
Standard - Electrical safety	IEC 61010-2-201 (SELV)
Standard – Safety extra-low voltage	IEC 61010-1 (SELV)
Standard – Safety extra-low voltage		IEC 61010-2-201 (PELV)
Standard - Safe isolation	IEC 61558-2-16
Standard - Safe isolation		IEC 61010-2-201
Standard - safety for equipment for measurement, control, and laboratory use	IEC 61010-1
Standard - Safety of transformers	EN 61558-2-16
Standard - power supply devices for low voltage with DC output	EN 61204-3
Overvoltage category
EN 61010-1	II (≤ 5000 m)
EN 62477-1	III (≤ 2000 m)

SIQ	CB-Scheme (IEC 61010-1, IEC 61010-2-201)
UL approvals	UL Listed UL 61010-1
		UL Listed UL 61010-2-201
		UL 1310 Class 2 Power Units
		ANSI/UL 121201 Class I, Division 2, Groups A, B, C, D (Hazardous Location)

EMC requirements for noise emission	EN 61000-6-3
EMC requirements for noise emission		EN 61000-6-4
EMC requirements for noise immunity	EN 61000-6-1
EMC requirements for noise immunity		EN 61000-6-2
Electromagnetic compatibility	Conformance with EMC Directive 2014/30/EU
EMC requirements, power plant	IEC 61850-3
EMC requirements, power plant		EN 61000-6-5
Conducted noise emission	EN 55016
Conducted noise emission		EN 61000-6-3 (Class B)
Noise emission	Additional basic standard EN 61000-6-5 (immunity in power station), IEC/EN 61850-3 (energy supply)
Noise emission	EN 55016
Noise emission		EN 61000-6-3 (Class B)
Harmonic currents
Frequency range	0 kHz ... 2 kHz
Flicker
Frequency range	0 kHz ... 2 kHz
Electrostatic discharge
Standards/regulations	EN 61000-4-2
Electrostatic discharge
Contact discharge	8 kV (Test Level 4)
Discharge in air	8 kV (Test Level 3)
Comments	Criterion A
Electromagnetic HF field
Standards/regulations	EN 61000-4-3
Electromagnetic HF field
Frequency range	80 MHz ... 1 GHz
Test field strength	20 V/m (Test Level X)
Frequency range	1 GHz ... 6 GHz
Test field strength	10 V/m (Test Level 3)
Comments	Criterion A
Fast transients (burst)
Standards/regulations	EN 61000-4-4
Fast transients (burst)
Input	4 kV (Test Level 4 - asymmetrical)
Output	4 kV (Test Level 4 - asymmetrical)
Signal	4 kV (Test Level 4 - asymmetrical)
Comments	Criterion A
Surge voltage load (surge)
Standards/regulations	EN 61000-4-5
Input	2 kV (Test Level 4 - symmetrical)
Input		4 kV (Test Level 4 - asymmetrical)
Output	1 kV (Test Level 3 - symmetrical)
Output		2 kV (Test Level 3 - asymmetrical)
Signal	0.5 kV (Test Level 2 - symmetrical)
Signal		1 kV (Test Level 2 - asymmetrical)
Comments	Criterion A
Conducted interference
Standards/regulations	EN 61000-4-6
Conducted interference
I/O/S	asymmetrical
Frequency range	0.15 MHz ... 80 MHz
Comments	Criterion A
Voltage	10 V (Test Level 3)
Power frequency magnetic field
Standards/regulations	EN 61000-4-8
Frequency	16.67 Hz
		50 Hz
		60 Hz
Test field strength	100 A/m
Additional text	60 s
Comments	Criterion A
Frequency	50 Hz
Frequency		60 Hz
Frequency range	50 Hz ... 60 Hz
Test field strength	1 kA/m
Additional text	3 s
Frequency	0 Hz
Test field strength	300 A/m
Additional text	DC, 60 s
Voltage dips
Standards/regulations	EN 61000-4-11
Voltage	100 V AC
Frequency	60 Hz
Voltage dip	70 %
Number of periods	0.5 / 1 / 30 periods
Additional text	Test Level 2
Comments	Criterion A
Voltage dip	40 %
Number of periods	5 / 10 / 50 periods
Additional text	Test Level 2
Comments	Criterion B
Voltage dip	0 %
Number of periods	0.5 / 1 / 5 / 50 periods
Additional text	Test Level 2
Comments	Criterion B
Pulse-shape magnetic field
Standards/regulations	EN 61000-4-9
Test field strength	1000 A/m
Comments	Criterion A
Attenuated sinusoidal oscillations (ring wave)
Standards/regulations	EN 61000-4-12
Input	2 kV (symmetrical)
Input		4 kV (asymmetrical)
Comments	Criterion A
Asymmetrical conducted disturbance variables
Test level 1	16.67 Hz 50 Hz 60 Hz (Test Level 3)
Voltage	30 V (Permanent)
Test level 2	16.67 Hz 50 Hz 60 Hz (Test Level 4)
Voltage	300 V (1 s)
Comments	Criterion A
Attenuated oscillating wave
Standards/regulations	EN 61000-4-18
Input/Output/Signal	1 kV (symmetrical)
Input/Output/Signal		2.5 kV (asymmetrical)
Comments	Criterion B
Criteria
Criterion A	Normal operating behavior within the specified limits.
Criterion B	Temporary impairment to operational behavior that is corrected by the device itself.
Criterion C	Temporary adverse effects on the operating behavior, which the device corrects automatically or which can be restored by actuating the operating elements.