PWT 100-800AC-FM - Lightning/surge arrester type 1/2 Phoenix Contact

Mã sản phẩm: 2800531

Danh mục: PHOENIX CONTACT, Supply, charge, and protect Phoenix Contact,

Lightning/surge arrester, according to type 1/2 / class I/II, for 3-phase power supply networks with combined PE and N installed in one conductor (L1, L2, L3, PEN).

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

General
Note	Assembling: Two 8 mm screws with 8 Nm on an isolated or grounded surface
		Long-wave surge current 2 ms in accordance with IEC 60099-4: 250 x 1.0 kA; 500 x 0.5 kA.

IEC test classification	I / II
IEC test classification		T1 / T2
EN type	T1 / T2
IEC power supply system	TN-C
IEC power supply system		IT
Type	Installation module
Product type	Arrester combination
Product family	POWERTRAB
Number of positions	3
Surge protection fault message	Optical, remote indicator contact
Insulation characteristics
Overvoltage category	8 kV: IV (600 V), III (1000 V)
Pollution degree	3

Nominal frequency f_N	50 Hz (60 Hz)
Nominal voltage U_N	690 V AC
Indicator/remote signaling
Connection name	Remote fault indicator contact
Switching function	2x N/C contacts, 1-pos.
Operating voltage	30 V AC
Operating voltage		30 V DC
Operating current	1.5 A AC
Operating current		1.5 A DC
Supply: Status indicator/remote signaling
Operating voltage	19.2 V AC/DC ... 30 V AC/DC
Operating current	7 mA AC/DC ... 13 mA AC/DC
Rated current	10 mA AC/DC
Max. required back-up fuse	1 A (e.g. T to IEC 127-2/III)
Immunity to interference according to IEC 61000-4-5 (line-line)	1 kV
Immunity to interference according to IEC 61000-4-5 (line-earth)	6 kV

Double terminal point
Connection method	Screw connection
Screw thread	M6
Tightening torque	8.5 Nm
Stripping length	24 mm
Conductor cross section flexible	16 mm² ... 50 mm²
Conductor cross section rigid	16 mm² ... 50 mm²
Conductor cross section AWG	6 ... 1/0
PE conductor connection
Connection method	Ring cable lug
Tightening torque	20 Nm
Conductor cross section flexible	16 mm² ... 95 mm²
Conductor cross section rigid	16 mm² ... 95 mm²
Conductor cross section AWG	6 ... 3/0
Remote fault indicator contact
Screw thread	M3
Tightening torque	0.55 Nm
Conductor cross section flexible	0.2 mm² ... 2.5 mm²
Conductor cross section rigid	0.2 mm² ... 2.5 mm²
Conductor cross section AWG	24 ... 12

Dimensional drawing
Width	176 mm
Height	191 mm
Depth	280 mm
Horizontal pitch	10 Div.

Color	silver grey
Color		gray
Flammability rating according to UL 94	V-2
CTI value of material	600
CTI value of material		250
Insulating material	PA/PC
Material group	I (PA 6.6/PC)
Material group		IIIa (PA 4.6)
Housing surface material	die-cast aluminum
Housing material	Die-cast aluminum, salt water resistant

Mechanical data
Open side panel	No

Mode of protection	L-PE
Direction of action	3L-PEN
Nominal voltage U_N	690 V AC
		554/960 V AC (TN-C)
		690 V AC (IT)
Nominal frequency f_N	50 Hz (60 Hz)
Maximum continuous operating voltage U_C (L-PE)	800 V AC
Rated load current I_L	150 A (Serial through wiring with 50 mm²)
Residual current I_PE	≤ 20 µA
Standby power consumption P_C	≤ 48 mVA
Nominal discharge current I_n (8/20) µs (L-PE)	35 kA
Maximum discharge current I_max (8/20) µs (L-PE)	100 kA
Impulse discharge current (10/350) µs (L-PE), charge	17.5 As
Impulse discharge current (10/350) µs (L-PE), specific energy	305 kJ/Ω
Impulse discharge current (10/350) µs (L-PE), peak current value I_imp	35 kA
Total discharge current I_total (10/350) µs	100 kA
Follow current interrupt rating I_fi (L-PE)	50 kA
Short-circuit current rating I_SCCR	50 kA
Voltage protection level U_p (L-PE)	≤ 4.5 kV
Residual voltage U_res (L-PE)	≤ 2.7 kV (at I_n)
		≤ 2.5 kV (at 20 kA)
		≤ 2.3 kV (at 10 kA)
		≤ 2.2 kV (at 5 kA)
		≤ 2.1 kV (at 3 kA)
TOV behavior at U_T (L-PE)	1960 V AC (200 ms / withstand mode)
TOV behavior at U_T (L-PE)		1500 V AC (5 s / withstand mode)
Response time t_A (L-PE)	≤ 100 ns
Max. backup fuse with V-type through wiring	125 A (gG at ≥35 mm²)
Max. backup fuse with branch wiring	400 A (gG at 2x 50 mm²)
Max. backup fuse with branch wiring		800 A (aR (only up to I_imp = 25 kA))

Ambient conditions
Degree of protection	IP20 (only when all terminal points are used)
Ambient temperature (operation)	-40 °C ... 80 °C
Ambient temperature (operation)		-40 °C ... 55 °C (serial through wiring ≥ 35 mm²)
Ambient temperature (storage/transport)	-40 °C ... 80 °C
Altitude	≤ 4000 m (amsl)
Permissible humidity (operation)	5 % ... 95 %
Shock (operation)	25g (Half-sine / 11 ms / 3x ±X, ±Y, ±Z)
Vibration (operation)	5g (10 ... 150 Hz / 2.5 h / X, Y, Z)
Vibration (operation)		4g (5 ... 100 Hz / X, Y, Z - according to GL )

UL specifications
Maximum continuous operating voltage MCOV (L-L)	800 V AC
Maximum continuous operating voltage MCOV (L-G)	800 V AC
Nominal discharge current I_n (L-L)	20 kA
Nominal discharge current I_n (L-G)	20 kA
Mode of protection	L-L
Mode of protection		L-G
Nominal voltage	690 V AC
Nominal voltage		400 V AC
Power distribution system	Wye
Power distribution system		Delta
Nominal frequency	60 Hz
Measured limiting voltage MLV (L-L)	8750 V
Measured limiting voltage MLV (L-G)	4370 V
SPD Type	4CA
UL indicator/remote signaling
AC operating voltage	30 V AC
DC operating voltage	30 V DC
AC operating current	1.5 A AC
DC operating current	1.5 A DC
UL connection data Double terminal point
Tightening torque	75 lb_f-in.
Conductor cross section AWG	1/0 ... 6
UL connection data PE conductor connection
Tightening torque	175 lb_f-in.
Conductor cross section AWG	3/0

Air clearances and creepage distances
Standards/regulations	DIN EN 60664-1 / EN 61643-11
Standards/specifications	IEC 61643-11
Standards/specifications	EN 61643-11