PV-FI-X1F/M-S 4-6 PU1 - Connector Phoenix Contact

Mã sản phẩm: 1533034

Danh mục: PHOENIX CONTACT, Kết nối (Connect) Phoenix Contact 2,

Photovoltaic PCB connector, product range: XLIX, connector, housing material: PC/PA, color: black, number of positions: 1, minimum conductor cross-section: 4 mm2, rated current: 35A, maximum conductor cross-section: 6 mm2, rated current: 40A, connection method: spring, contact type: socket plug

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

Safety note
Safety note	• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
		• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
		WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
		• The products are suitable for applications in plant, controller, and electrical device engineering.
		• Assembled products may not be manipulated or improperly opened.
		• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
		• When using the product in direct connection with third-party manufacturers, the user is responsible.
		• For operating voltages > 50 V AC, conductive connector housings must be grounded
		• Ensure that the protective or functional ground has been properly connected.
		• Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product
		• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
		• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
		• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).
		• Operate the connector only when it is fully plugged in and interlocked.
		• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
		• Observe the minimum bending radius of the cable. Lay the cable without twisting it.

Product type	Photovoltaic connector
Number of positions	1
Insulation characteristics
Protection class	III
Degree of pollution	2

Rated voltage (II/2)	1500 V
Rated surge voltage	16 kV
Rated surge voltage (III/2)	16 kV
Rated surge voltage (III/3)	16 kV
Rated current	35 A
Rated current (6.0 mm²)	40 A
Contact resistance	≤ 0.5 mΩ
Nominal voltage U_N	1500 V

Color	black
Flammability rating according to UL 94	V0
Insulating material	PC/PA
Contact surface	Ag
Contact material	Cu
Contact surface material	Sn

Cable type	PV cable
External cable diameter	5 mm ... 8 mm
Single wire, cross section	4 mm² 6 mm²
Cable pull-out force	> 80 N
Resistance to oil	no

Mechanical data
Insertion/withdrawal cycles	50

Ambient conditions
Degree of protection	IP66 / IP68 (2 m / 24 h) (After connection)
Degree of protection		IP20 (Not plugged in)
Ambient temperature (operation)	-40 °C ... 85 °C
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Ambient temperature (assembly)	-25 °C ... 50 °C
Resistance to oil	no