PSR-SPP- 24UC/ESL4/3X1/1X2/B - Safety relays Phoenix Contact

Mã sản phẩm: 2981062

Danh mục: PHOENIX CONTACT, Switch, Measure and Monitor Phoenix Contact,

Safety relay for emergency stop, safety door, and light grid monitoring up to SIL 3 or Cat. 4, PL e in accordance with EN ISO 13849, 1- or 2-channel operation, 3 enabling current paths, nominal input voltage: 24 V AC/DC, plug-in Push-in terminal block

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

Product type	Safety relays
Product family	PSRclassic
Application	Emergency stop
		Safety door
		Light grid
Mechanical service life	approx. 10⁷ cycles
Relay type	Electromechanical relay with force-guided contacts in accordance with IEC/EN 61810-3

Maximum power dissipation for nominal condition	1.68 W
Nominal operating mode	100% operating factor
Air clearances and creepage distances between the power circuits
Rated insulation voltage	250 V
Rated surge voltage/insulation	4 kV / basic insulation (safe isolation, reinforced insulation, and 6 kV between A1-A2/logic/enabling and signaling current paths)

General
Nominal input voltage U_N	24 V AC/DC
Input voltage range in reference to U_N	0.85 ... 1.1
Typical input current at U_N	150 mA AC
Typical input current at U_N		70 mA DC
Voltage at input/start and feedback circuit	approx. 24 V DC
Typical response time	25 ms (manual start)
Typical response time		100 ms (automatic start)
Typical release time	10 ms
Concurrence	∞
Recovery time	1 s
Protective circuit	Fuse; PTC resistor
Protective circuit		Surge protection; Suppressor diode
Operating voltage display	Green LED
Status display	Green LED

Contact type	3 enabling current paths
Contact type		1 signaling current path
Contact material	AgSnO₂, + 0.2 µm Au
Maximum switching voltage	250 V AC/DC
Minimum switching voltage	15 V AC/DC
Limiting continuous current	6 A
Maximum inrush current	6 A
Inrush current, minimum	25 mA
Sq. Total current	72 A² (I_TH² = I₁² + I₂² + I₃²)
Interrupting rating (ohmic load) max.	144 W (24 V DC, τ = 0 ms)
		288 W (48 V DC, τ = 0 ms)
		77 W (110 V DC, τ = 0 ms)
		88 W (220 V DC, τ = 0 ms)
		1500 VA (250 V AC, τ = 0 ms)
Maximum interrupting rating (inductive load)	48 W (24 V DC, τ = 40 ms)
		40 W (48 V DC, τ = 40 ms)
		35 W (110 V DC, τ = 40 ms)
		33 W (220 V DC, τ = 40 ms)
Switching capacity min.	0.4 W
Switching capacity (360/h cycles)	6 A (24 V DC)
Switching capacity (360/h cycles)		5 A (230 V AC)
Switching capacity (3600/h cycles)	3 A (24 V (DC13))
Switching capacity (3600/h cycles)		3 A (230 V (AC 15))
Output fuse	10 A gL/gG NEOZED (N/O contact)

Connection technology
pluggable	yes
Conductor connection
Connection method	Push-in connection
Conductor cross section rigid	0.2 mm² ... 1.5 mm²
Conductor cross section flexible	0.2 mm² ... 1.5 mm²
Conductor cross section, flexible, with ferrule, with plastic sleeve	0.25 mm² ... 1.5 mm² (only together with CRIMPFOX 6)
Conductor cross section flexible, with ferrule without plastic sleeve	0.25 mm² ... 1.5 mm² (only together with CRIMPFOX 6)
Conductor cross-section AWG	24 ... 16
Stripping length	8 mm

Width	22.5 mm
Height	112 mm
Depth	114.5 mm

Housing material

Polyamide

Safety data
Stop category	0
Safety data: EN ISO 13849
Category	4
Performance level (PL)	e
Safety data: IEC 61508 - High demand
Designation	Data only applies if the safety function is demanded at least once a year and the signal contact is read back.
Safety Integrity Level (SIL)	3
SFF_{Single-channel}	100 %
SFF_Two-channel	96.11 %
Mean time to a dangerous failure (MTTF_D)	205243 Years
Probability of a hazardous failure per hour (PFH_D)	5.56 x 10^-10
Diagnostic coverage (DC)	91.1 %
Proof test interval	240 Months
Duration of use	240 Months
Safety data: IEC 61508 - Low demand
Designation	The data is only valid if the demand rate is no more than once a year.
Safety Integrity Level (SIL)	3
SFF_{Single-channel}	100 %
SFF_Two-channel	80.35 %
Mean time to a dangerous failure (MTTF_D)	17913 Years
Probability of a hazardous failure on demand (PFD_AVG)	1.50 x 10^-4
Diagnostic coverage (DC)	0 %
Proof test interval	75 Months
Duration of use	240 Months

Ambient conditions
Degree of protection	IP20
Min. degree of protection of inst. location	IP54
Ambient temperature (operation)	-20 °C ... 55 °C
Ambient temperature (storage/transport)	-40 °C ... 70 °C
Maximum altitude	≤ 2000 m (Above sea level)
Max. permissible humidity (storage/transport)	75 % (on average, 85% infrequently, non-condensing)
Max. permissible relative humidity (operation)	75 % (on average, 85% infrequently, non-condensing)
Shock	15g
Vibration (operation)	10 Hz ... 150 Hz, 2g