PSR-MC38-2NO-1DO-24DC-PI - Safety relays Phoenix Contact

Mã sản phẩm: 1009832

Danh mục: PHOENIX CONTACT, Switch, Measure and Monitor Phoenix Contact,

Safety relay for emergency stop, safety doors and light grids up to SIL 3, Cat. 4, PL e, 1- or 2-channel operation, automatic or manual, monitored start, 2 enabling current paths, 1 signal output, TBUS interface, US = 24 V DC, pluggable push-in terminal

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

Product type	Safety relays
Product family	PSRmini
Application	Emergency stop
		Safety door
		Light grid
		Solenoid switch
		Transponder
Relay type	Electromechanical relay with force-guided contacts in accordance with IEC/EN 61810-3
Times
Typical response time	30 ms (manual, monitored start)
Typical response time		200 ms (automatic start)
Typ. starting time with U_s	200 ms (when controlled via A1)
Typical release time	25 ms (when actuation is via the sensor circuit)
Typical release time		60 ms (when controlled via A1)
Restart time	< 1 s (Boot time)
Recovery time	< 500 ms

Maximum power dissipation for nominal condition	16.6 W (at U_S = 26.4 V, I_L² = 72 A²)
Nominal operating mode	100% operating factor
Air clearances and creepage distances between the power circuits
Rated insulation voltage	250 V
Rated insulation voltage		250 V
Supply
Designation	A1/A2
Rated control circuit supply voltage U_S	20.4 V DC ... 26.4 V DC
Rated control circuit supply voltage U_S	24 V DC -15 % / +10 % (provide external protection)
Rated control supply current I_S	typ. 75 mA
Power consumption at U_S	typ. 1.8 W
Inrush current	< 4 A (Δt = 3 ms at U_s)
Filter time	20 ms (at A1 in the event of voltage dips at U_s)
Protective circuit	Serial protection against polarity reversal; Suppressor diode

Digital: Sensor circuit (S10, S12, S13, S22)
Description of the input	safety-related sensor inputs
Number of inputs	4
Input voltage range "1" signal	20.4 V DC ... 26.4 V DC
Inrush current	< 40 mA (typ. with U_S at S10)
		< 300 mA (typ. with U_S at S12, Δt = 150 ms)
		< 3 mA (Typically with U_S at S13)
		> -300 mA (Typically with U_S at S22, Δt = 150 ms)
Filter time	2 ms (At S10, S12, S13; test pulse width of low test pulses)
		1 s (At S10, S12, S13; test pulse rate of low test pulses)
		No brightness test pulses / high test pulses permitted.
Concurrence	∞
Max. permissible overall conductor resistance	50 Ω
Protective circuit	Suppressor diode
Current consumption	40 mA (typ. with U_S at S10)
		45 mA (Typically with U_S at S12)
		3 mA (Typically with U_S at S13)
		-35 mA (Typically with U_S at S22, Δt = 150 ms)
Digital: Start circuit (Y1, S34, S35)
Description of the input	non-safety-related
Input voltage range "1" signal	20.4 V DC ... 26.4 V DC
Inrush current	< 60 mA (Typically with U_S at Y1, Δt = 150 ms)
		< 270 mA (Typically with U_S at S34, Δt = 15 ms)
		< 80 mA (Typically with U_S at S35, Δt = 25 ms)
Filter time	No darkness test pulses / low test pulses permitted. No brightness test pulses / high test pulses permitted.
Max. permissible overall conductor resistance	50 Ω
Protective circuit	Suppressor diode
Current consumption	typ. 10 mA (Typically with U_S at Y1)
Current consumption		typ. 34 µA (Typically with U_S at S35)

Relay: Enabling current path (13/14, 23/24)
Output description	safety-related N/O contacts
Output description		2 NO contacts each in series, without delay, floating
Number of outputs	2 (undelayed)
Contact type	2 enabling current paths
Contact material	AgSnO₂
Switching voltage	min. 10 V AC/DC
Switching voltage		max. 250 V AC/DC (Observe the load curve)
Switching capacity	min. 100 mW
Inrush current	min. 10 mA
Inrush current		max. 6 A
Switching capacity in accordance with IEC 60947-5-1	5 A (24 V (DC13))
Switching capacity in accordance with IEC 60947-5-1		5 A (250 V (AC15))
Limiting continuous current	6 A
Sq. Total current	72 A² (observe derating)
Switching frequency	max. 0.5 Hz
Mechanical service life	10x 10⁶ cycles
Output fuse	10 A gL/gG
Output fuse		4 A gL/gG (for low-demand applications)
Signal: Y30
Output description	PNP
Output description		non-safety-related
Number of outputs	1
Voltage	approx. 23.9 V DC (U_s - 0.1 V)
Current	max. 100 mA
Maximum inrush current	500 mA (Δt = 1 ms at U_s)
Protective circuit	Suppressor diode

Connection technology
pluggable	yes
Conductor connection
Connection method	Push-in connection
Conductor cross section rigid	0.2 mm² ... 2.5 mm²
Conductor cross section flexible	0.2 mm² ... 2.5 mm²
Conductor cross-section AWG	24 ... 16
Stripping length	10 mm

Status display	4 x green LEDs
Operating voltage display	1 x green LED

Width	22.5 mm
Height	117.5 mm
Depth	114.5 mm

Housing material

Polyamide

Safety data
Stop category	0
Safety data: EN ISO 13849
Category	4 (5 A DC13; 5 A AC15; 8760 switching cycles/year)
Performance level (PL)	e
Safety data: IEC 61508 - High demand
Equipment type	Type A
Safety Integrity Level (SIL)	3
Probability of a hazardous failure per hour (PFH_D)	1.00 x 10^-9 (5 A DC13; 5 A AC15; 8760 switching cycles/year)
Proof test interval	240 Months
Duration of use	240 Months
Safety data: IEC 61508 - Low demand
Equipment type	Type A
Safety Integrity Level (SIL)	3
Probability of a hazardous failure on demand (PFD_AVG)	8.24 x 10^-5
Proof test interval	40 Months
Duration of use	240 Months

Ambient conditions
Degree of protection	IP20
Min. degree of protection of inst. location	IP54
Ambient temperature (operation)	-20 °C ... 55 °C (observe derating)
Ambient temperature (storage/transport)	-40 °C ... 70 °C
Maximum altitude	≤ 2000 m (Above sea level)
Max. permissible humidity (storage/transport)	75 % (on average, 85% infrequently, non-condensing)
Max. permissible relative humidity (operation)	75 % (on average, 85% infrequently, non-condensing)
Shock	15g
Vibration (operation)	10 Hz ... 150 Hz, 2g