PSR-MC20-3NO-1DO-24DC-SP - Safety relays Phoenix Contact

Mã sản phẩm: 2700467

Danh mục: PHOENIX CONTACT, Switch, Measure and Monitor Phoenix Contact,

Safety relay for emergency stop / safety doors up to SIL 1, Cat. 1, PL c, depending on the application up to SIL 3, Cat. 4, PL e, 1-channel operation, automatic / manual start, 3 enabling current paths, US = 24 V DC, pluggable Push-in terminal block

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

Product type	Safety relays
Product family	PSRmini
Application	Emergency stop
		Safety door
		Solenoid switch
Relay type	Electromechanical relay with force-guided contacts in accordance with IEC/EN 61810-3
Times
Typical response time	< 175 ms (automatic start)
Typical response time		< 175 ms (manual, monitored start)
Typ. starting time with U_s	< 250 ms (when controlled via A1)
Typical release time	< 20 ms (when controlled via A1 or S12)
Recovery time	< 500 ms

Nominal operating mode	100% operating factor
Air clearances and creepage distances between the power circuits
Rated insulation voltage	250 V AC
Rated insulation voltage		250 V AC
Rated surge voltage/insulation	Safe isolation, reinforced insulation 6 kV between input circuit and enabling current path (13/14) and enabling current path (23/24) and enabling current path (33/34) Basic insulation 4 kV between all current paths and housing
Supply
Designation	A1/A2
Rated control circuit supply voltage U_S	20.4 V DC ... 26.4 V DC
Rated control circuit supply voltage U_S	24 V DC -15 % / +10 %
Rated control supply current I_S	typ. 80 mA
Power consumption at U_S	typ. 1.92 W
Inrush current	5 A (Δt = 200 µs at U_s)
Filter time	1 ms (at A1 in the event of voltage dips at U_s)
Protective circuit	Surge protection; Suppressor diode
Protective circuit		Protection against polarity reversal for rated control circuit supply voltage

Digital: Sensor circuit (S11, S12)
Description of the input	safety-related sensor inputs
Input voltage range "0" signal	0 V DC ... 5 V DC (for safe Off; at S12)
Input current range "0" signal	0 mA ... 2 mA (for safe Off; at S12)
Inrush current	< 21 mA (with U_s/I_xto S12)
Filter time	max. 1.5 ms (at S12; test pulse width)
		min. 7.5 ms (at S12; test pulse rate)
		Test pulse rate = 5 x Test pulse width
Max. permissible overall conductor resistance	150 Ω
Current consumption	< 5 mA (with U_s/I_xto S12)
Digital: Start circuit (S34)
Description of the input	non-safety-related
Number of inputs	1
Input voltage range "1" signal	20.4 V DC ... 26.4 V DC
Inrush current	typ. 200 mA
Max. permissible overall conductor resistance	150 Ω
Protective circuit	Suppressor diode
Current consumption	< 10 mA (at S34/24 V)
Current consumption		> -5 mA (at S34/0 V)

Relay: Enabling current paths (13/14, 23/24, 33/34)
Output description	safety-related N/O contacts
Number of outputs	3 (undelayed)
Contact type	3 enabling current paths
Contact material	AgSnO₂
Switching voltage	min. 12 V AC/DC
Switching voltage		max. 250 V AC/DC (Observe the load curve)
Switching capacity	min. 60 mW
Inrush current	min. 3 mA
Inrush current		max. 6 A
Limiting continuous current	6 A (observe derating)
Sq. Total current	48 A² (observe derating)
Switching frequency	0.5 Hz
Mechanical service life	10x 10⁶ cycles
Output fuse	6 A gL/gG (N/O contact)
Output fuse		4 A gL/gG (for low-demand applications)
Signal: M1
Output description	non-safety-related
Number of outputs	1 (digital, PNP)
Voltage	22 V DC (U_s - 2 V)
Current	max. 100 mA
Maximum inrush current	500 mA (Δt = 1 ms at U_s)
Short-circuit protection	no

Connection technology
pluggable	yes
Conductor connection
Connection method	Push-in connection
Conductor cross section rigid	0.2 mm² ... 1.5 mm²
Conductor cross section flexible	0.2 mm² ... 1.5 mm²
Conductor cross section, flexible, with ferrule, with plastic sleeve	0.25 mm² ... 1.5 mm² (only together with CRIMPFOX 6)
Conductor cross section flexible, with ferrule without plastic sleeve	0.25 mm² ... 1.5 mm² (only together with CRIMPFOX 6)
Conductor cross-section AWG	24 ... 16
Stripping length	8 mm

Status display	3 x green LED
Operating voltage display	1 x green LED

Width	12.5 mm
Height	116.6 mm
Depth	114.5 mm

Housing material

Polyamide

Safety data
Stop category	0
Safety data: EN ISO 13849
Category	1 (up to Cat. 4 depending on the application)
Performance level (PL)	c (up to PL e depending on the application)
Safety data: IEC 61508 - High demand
Safety Integrity Level (SIL)	1 (up to SIL 3 depending on the application)
Probability of a hazardous failure per hour (PFH_D)	1.5 x 10^-9 (4 A DC13; 5 A AC15; 8760 switching cycles/year)
Proof test interval	240 Months
Duration of use	240 Months
Safety data: IEC 61508 - Low demand
Safety Integrity Level (SIL)	1 (up to SIL 3 depending on the application)
Probability of a hazardous failure on demand (PFD_AVG)	1.46 x 10^-4
Proof test interval	60 Months
Duration of use	240 Months

Ambient conditions
Degree of protection	IP20
Min. degree of protection of inst. location	IP54
Ambient temperature (operation)	-40 °C ... 55 °C (observe derating)
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Maximum altitude	≤ 2000 m (Above sea level)
Max. permissible humidity (storage/transport)	75 % (on average, 85% infrequently, non-condensing)
Max. permissible relative humidity (operation)	75 % (on average, 85% infrequently, non-condensing)
Shock	15g
Vibration (operation)	10 Hz ... 150 Hz, 2g