PSM-ME-RS232/TTY-P - Interface converter Phoenix Contact

Mã sản phẩm: 2744458

Interface converter, for converting RS-232 (V.24) to TTY, with electrical isolation, 2 channels, rail-mountable

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Utilization restriction
EMC note	EMC: class A product, see manufacturer's declaration in the download area
Utilization restriction
CCCex note	Use in potentially explosive areas is not permitted in China.

Product type	Interface converter
MTBF	1989 Years (Telcordia standard, 25°C temperature, 21% operating cycle (5 days a week, 8 hours a day))
MTBF		410 Years (Telcordia standard, 40°C temperature, 34.25% operating cycle (5 days a week, 12 hours a day))

Electrical isolation	VCC // V.24 (RS-232) // TTY
Maximum power dissipation for nominal condition	1.8 W
Test voltage data interface/power supply	2 kV_rms (50 Hz, 1 min.)
Test voltage data interface/power supply		2 kV AC
Test voltage data interfaces	2 kV AC
Supply
Nominal supply voltage	24 V AC/DC ±20 % (via pluggable COMBICON screw terminal block)
Typical current consumption	75 mA (24 V DC)
Protective circuit	Surge protection; Suppressor diode

Supply
Tightening torque	0.56 Nm ... 0.79 Nm

Bit distortion	< 5 %
Bit delay	< 3 µs
Signal	Modbus
Transmission channels	2 (1/1), RxD, TxD, full duplex
Data: V.24 (RS-232) interface in acc. with ITU-T V.28, EIA/TIA-232, DIN 66259-1
Serial transmission speed	≤ 19.2 kbps
Connection method	D-SUB 9 plug
Pin assignment	DTE/DCE switchover via switch
Transmission length	15 m (shielded twisted pair)
Conductor cross section flexible max.	2.5 mm²
Conductor cross section flexible min.	0.2 mm²
Max. AWG conductor cross section, flexible	13
Min. AWG conductor cross section, flexible	24
Protocols supported	transparent protocol
Data: TTY interface, CL2 in acc. with DIN 66348-1
Serial transmission speed	≤ 19.2 kbps
Connection method	Pluggable screw connection
Transmission length	1000 m (shielded twisted pair)
Conductor cross section flexible max.	2.5 mm²
Conductor cross section flexible min.	0.2 mm²
Conductor cross section AWG max.	13
Conductor cross section AWG min.	24
Load/output load current output	≤ 500 Ω
Impedance	≤ 117 Ω (Output)
Impedance		126 Ω (Input)
Output current	2x 20 mA ±10 % (Loop current)

Material Housing

Ambient conditions
Degree of protection	IP20
Ambient temperature (operation)	0 °C ... 55 °C
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Altitude	≤ 5000 m (For restrictions, see the manufacturer's declaration for altitude operation)
Permissible humidity (operation)	10 % ... 95 % (non-condensing)

CE
Certificate	CE-compliant
EAC
Identification	EAC
UL, USA/Canada
Identification	508 Recognized
		Class I, Div. 2, Groups A, B, C, D
		Class I, Zone 2, AEx nA IIC T4
		Class I, Zone 2, Ex nA IIC T4 Gc X
Corrosive gas test
Identification	ISA-S71.04-1985 G3 Harsh Group A
Shipbuilding
Identification	DNV GL
DNV GL data
Temperature	B
Humidity	A
Vibration	A
EMC	B
Enclosure	Required protection according to the Rules shall be provided upon installation on board

Noise immunity	EN 61000-6-2:2005
Electromagnetic compatibility	Conformance with EMC Directive 2014/30/EU
Noise emission	EN 61000-6-4
Electrostatic discharge
Standards/regulations	EN 61000-4-2
Electrostatic discharge
Contact discharge	± 6 kV (Test Level 3)
Discharge in air	± 8 kV (Test Level 3)
Comments	Criterion B
Electromagnetic HF field
Standards/regulations	EN 61000-4-3
Electromagnetic HF field
Frequency range	Test Level 3
Field intensity	10 V/m
Comments	Criterion A
Fast transients (burst)
Standards/regulations	EN 61000-4-4
Fast transients (burst)
Input	± 4 kV (5 kHz)
Signal	± 2 kV (5 kHz)
Comments	Criterion B
Surge current load (surge)
Standards/regulations	EN 61000-4-5
Surge current load (surge)
Input	± 0.5 kV (2 Ω)
Signal	± 2 kV (42 Ω)
Comments	Criterion B
Conducted interference
Standards/regulations	EN 61000-4-6
Conducted interference
Comments	Criterion A
Voltage	10 V
Emitted interference
Standards/regulations	EN 55011
Comments	Class A, industrial applications
Criteria
Criterion A	Normal operating behavior within the specified limits.
Criterion B	Temporary impairment to operational behavior that is corrected by the device itself.