PSI-TERMINATOR-PB-TBUS - Termination resistor Phoenix Contact

Mã sản phẩm: 2702636

Danh mục: PHOENIX CONTACT, Tự động hóa Phoenix Contact,

Active termination resistor for PROFIBUS and RS-485 bus systems, redundant power supply, routing of the supply voltage via DIN rail connector, electrical isolation, switchable termination, integrated programming interface

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

Utilization restriction
EMC note	EMC: class A product, see manufacturer's declaration in the download area
Utilization restriction
CCCex note	Use in potentially explosive areas is not permitted in China.

Product type	Terminal resistor
MTTF	3305 Years (SN 29500 standard, temperature 25°C, operating cycle 21%)
		1923 Years (SN 29500 standard, temperature 40°C, operating cycle 34.25%)
		911 Years (SN 29500 standard, temperature 40°C, operating cycle 100%)
Insulation characteristics
Overvoltage category	II
Insulation characteristics
Pollution degree	2

Electrical isolation	RS-485 // VCC
Maximum power dissipation for nominal condition	0.24 W
Test voltage data interface/power supply	1.5 kV AC (50 Hz, 1 min.)
Supply
Supply voltage range	18 V DC ... 30 V DC (via pluggable COMBICON screw terminal block)
Nominal supply voltage	24 V DC (via pluggable COMBICON screw terminal block)
Typical current consumption	10 mA (24 V DC, no load on D-SUB)
Typical current consumption		60 mA (24 V DC, current drain at D-SUB of 150 mA)
Max. current consumption	12 mA (18 V DC, no load on D-SUB)
Max. current consumption		77 mA (18 V DC, current drain at D-SUB of 150 mA)
Function
Status and diagnostic indicators	LEDs: US (power supply), ACT (data activity)

Supply
Conductor cross section, flexible	0.20 mm² ... 2.50 mm²
Conductor cross section, rigid	0.20 mm² ... 2.50 mm²
Conductor cross section, flexible [AWG]	24 ... 12
Tightening torque	0.6 Nm ... 0.8 Nm

Signal	Modbus
Signal		PROFIBUS
Data: PROFIBUS acc. to IEC 61158, RS-485 2-conductor
Serial transmission speed	≤ 12 Mbps
Connection method	D-SUB-9, COMBICON
Transmission length	≤ 1200 m (Depends on transmission speed and cable type)
Termination resistor	390 Ω
		220 Ω
		390 Ω (Can be connected)
Conductor cross section flexible max.	1.5 mm²
Conductor cross section flexible min.	0.2 mm²
Conductor cross section, rigid max.	1.5 mm²
Conductor cross section, rigid min.	0.2 mm²
Max. AWG conductor cross section, flexible	16
Min. AWG conductor cross section, flexible	24
Single-wire/terminal point, rigid AWG max.	16
Single-wire/terminal point, rigid AWG min.	24
Output nominal voltage	5 V DC

Dimensional drawing
Width	22.5 mm
Height	92 mm
Depth	73 mm

Material Housing

PA 6.6-FR

Ambient conditions
Degree of protection	IP20
Ambient temperature (operation)	-40 °C ... 70 °C
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Altitude	≤ 5000 m (For restrictions, see the manufacturer's declaration for altitude operation)
Altitude		≤ 2000 m (Restrictions for ATEX applications)
Permissible humidity (operation)	10 % ... 95 % (non-condensing)
Air pressure (operation)	≤ 80 kPa (When used in EX zone 2)

CE
Certificate	CE-compliant
ATEX
Identification	 II 3 G Ex nA IIC T4 Gc X
Note	Please follow the special installation instructions in the documentation!
UL, USA/Canada
Identification	508 Listed
Corrosive gas test
Identification	ISA-S71.04-1985 G3 Harsh Group A

Electromagnetic compatibility	Conformance with EMC Directive 2014/30/EU
Electrostatic discharge
Standards/regulations	EN 61000-4-2
Electrostatic discharge
Contact discharge	± 6 kV (Test Level 3)
Discharge in air	± 8 kV (Test Level 3)
Indirect discharge	± 6 kV
Comments	Criterion B
Electromagnetic HF field
Standards/regulations	EN 61000-4-3
Electromagnetic HF field
Frequency range	80 MHz ... 3 GHz (Test Level 3)
Field intensity	10 V/m
Comments	Criterion A
Fast transients (burst)
Standards/regulations	EN 61000-4-4
Fast transients (burst)
Input	± 2.2 kV (Test Level 3)
Signal	± 2.2 kV (Test Level 3)
Comments	Criterion B
Surge current load (surge)
Standards/regulations	EN 61000-4-5
Surge current load (surge)
Input	± 0.5 kV (sym. / asym.)
Signal	± 1 kV (Data line, asymmetrical)
Comments	Criterion B
Conducted interference
Standards/regulations	EN 61000-4-6
Conducted interference
Frequency range	0.15 MHz ... 80 MHz
Comments	Criterion A
Voltage	10 V
Emitted interference
Standards/regulations	EN 55011
Comments	Class A, industrial applications
Criteria
Criterion A	Normal operating behavior within the specified limits.
Criterion B	Temporary impairment to operational behavior that is corrected by the device itself.