PSI-MOS-PROFIB/FO1300 E - FO converters Phoenix Contact

Mã sản phẩm: 2708559

Danh mục: PHOENIX CONTACT, Tự động hóa Phoenix Contact,

Fiber optic converter with integrated optical diagnostics, alarm contact, for PROFIBUS up to 12 Mbps, termination device with one fiber optic interface (SC-Duplex), 1300 nm, for fiberglass cable

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

Utilization restriction
CCCex note	Use in potentially explosive areas is not permitted in China.

Product type	Media converter
MTTF	849 Years (SN 29500 standard, temperature 25°C, operating cycle 21%)
		392 Years (SN 29500 standard, temperature 40°C, operating cycle 34.25%)
		163 Years (SN 29500 standard, temperature 40°C, operating cycle 100%)
MTBF	406 Years (Telcordia standard, 25°C temperature, 21% operating cycle (5 days a week, 8 hours a day))
MTBF		92 Years (Telcordia standard, 40°C temperature, 34.25% operating cycle (5 days a week, 12 hours a day))

Electrical isolation	VCC // RS-485
Maximum power dissipation for nominal condition	1.32 W
Test voltage data interface/power supply	1.5 kV_rms (50 Hz, 1 min.)
Supply
Supply voltage range	18 V DC ... 32 V DC (via pluggable COMBICON screw terminal block)
Nominal supply voltage	24 V DC (in acc. with UL)
Typical current consumption	55 mA (24 V DC)
Max. current consumption	90 mA
Max. current consumption		≤ 2 A (For operation in a joining station, via the DIN rail connector)
Connection method	COMBICON plug-in screw terminal block

Switching
Output name	Relay output
Output description	Alarm output
Number of outputs	1
Maximum switching voltage	60 V DC (Resistive Load, General Load)
		30 V AC (Resistive load)
		42 V AC (peak, resistive load)
Limiting continuous current	0.46 A

Supply
Connection method	COMBICON plug-in screw terminal block
Stripping length	7 mm
Tightening torque	0.56 Nm ... 0.79 Nm

Bit distortion, input	± 35 % (permitted)
Bit distortion, output	< 6.25 %
Bit delay	< 1 bit (DIP 7 = OFF, standard operation)
Bit delay		11 bit (DIP 7 = ON, redundancy operation)
Signal	PROFIBUS
Data: optical FO
No. of channels	1
Transmit capacity, minimum	-3.4 dBm (50/125 μm, multimode fiberglass)
		-4.7 dBm (62.5/125 μm, multimode fiberglass)
		-5.5 dBm (9/125 μm, singlemode fiberglass)
Transmission length incl. 3 dB system reserve	25 km (With F-G 50/125 0.7 dB/km at 1300 nm)
		22 km (with F-G 62.5/125 0.8 dB/km at 1300 nm)
		45 km (With F-E 9/125 0,4 dB/km at 1300 nm)
Transmission protocol	Protocol-transparent to the RS-485 interface
Connection method	SC duplex
Wavelength	1300 nm
Minimum receiver sensitivity	-25.5 dBm (Multi mode)
Minimum receiver sensitivity		-26.5 dBm (Singlemode)
Maximum receiver sensitivity	0 dBm
Transmission medium	Multi-mode fiberglass
Transmission medium		Single-mode fiberglass
Data: PROFIBUS acc. to IEC 61158, RS-485 2-wire, half duplex, automatic control
Serial transmission speed	≤ 12 Mbps
Connection method	D-SUB-9 female connector
Transmission length	≤ 1200 m (depending on the data rate, with shielded, twisted pair data cable)
Conductor cross section flexible max.	2.5 mm²
Conductor cross section flexible min.	0.2 mm²
Conductor cross section, rigid max.	2.5 mm²
Conductor cross section, rigid min.	0.2 mm²
Max. AWG conductor cross section, flexible	14
Min. AWG conductor cross section, flexible	24
Single-wire/terminal point, rigid AWG max.	14
Single-wire/terminal point, rigid AWG min.	24
Transmission medium	2-wire twisted pair, shielded
File format/coding	UART (11 Bit, NRZ)
Data direction switching	Automatic control
Output nominal voltage	5 V DC ±0.25 (50 mA)

Dimensional drawing
Width	35 mm
Height	105 mm
Depth	106 mm

Material Housing

PA 6.6-FR

FO cable
Fiber types	50/125 µm
		62.5/125 µm
		9/125 µm
		Fiberglass

Ambient conditions
Degree of protection	IP20
Ambient temperature (operation)	-20 °C ... 60 °C
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Altitude	≤ 5000 m (For restrictions, see the manufacturer's declaration for altitude operation)
Altitude		≤ 2000 m (Hazardous locations)
Permissible humidity (operation)	30 % ... 95 % (non-condensing)

CE
Certificate	CE-compliant
ATEX
Identification	 II 3 G Ex ec IIC T4 Gc
Certificate	UL 21 ATEX 2550X
Note	Please follow the special installation instructions in the documentation!
IECEx
Identification	Ex ec IIC T4 Gc
Certificate	IECEx ULD 21.00013X
UL, USA/Canada
Identification	Class I, Zone 2, AEx ec IIC T4 Gc
		Ex ec IIC T4 Gc X
		Class I, Div. 2, Groups A, B, C, D
Corrosive gas test
Identification	ISA-S71.04-1985 G3 Harsh Group A

Noise immunity	EN 61000-6-2:2005
Electromagnetic compatibility	Conformance with EMC Directive 2014/30/EU
Noise emission	EN 55011
Electrostatic discharge
Standards/regulations	EN 61000-4-2
Electrostatic discharge
Contact discharge	± 6 kV
Discharge in air	± 8 kV
Comments	Criterion B
Electromagnetic HF field
Standards/regulations	EN 61000-4-3
Electromagnetic HF field
Field intensity	10 V/m
Comments	Criterion A
Fast transients (burst)
Standards/regulations	EN 61000-4-4
Fast transients (burst)
Input	± 2 kV
Signal	± 2 kV
Comments	Criterion B
Surge current load (surge)
Standards/regulations	EN 61000-4-5
Surge current load (surge)
Input	± 0.5 kV
Signal	± 1 kV
Comments	Criterion B
Conducted interference
Standards/regulations	EN 61000-4-6
Conducted interference
Comments	Criterion A
Voltage	10 V
Emitted interference
Standards/regulations	EN 55011
Comments	Class A, industrial applications
Criteria
Criterion A	Normal operating behavior within the specified limits.
Criterion B	Temporary impairment to operational behavior that is corrected by the device itself.