PRC 3-FC-MS6 8-21 - Connector Phoenix Contact

Mã sản phẩm: 1014498

Danh mục: PHOENIX CONTACT, Kết nối (Connect) Phoenix Contact,

Installation connector, Range of articles: PRC 35, Connector, design: Release with tool or by hand (see accessories), housing material: PPE, color: black, number of positions: 3, min. conductor cross section: 1.5 mm2, max. conductor cross section: 6 mm2, rated voltage: 690 V AC, rated current: 35 A, Connection method: Screw connection, Type of contact: Pin, min. cable diameter: 8 mm, max. cable diameter: 21 mm. Ensures touch protection

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

General	Ensures touch protection
General	For assembly notes, please refer to the packing slip
Safety note
Safety note	• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
		• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
		WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
		• Assembled products may not be manipulated or improperly opened.
		• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
		• When using the product in direct connection with third-party manufacturers, the user is responsible.
		• For operating voltages > 50 V AC, conductive connector housings must be grounded
		• Ensure that the protective or functional ground has been properly connected.
		• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
		• Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product
		• Only use tools recommended by Phoenix Contact
		• The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
		• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
		• Operate the connector only when it is fully plugged in.
		• Operate the connector only when it is fully plugged in and interlocked.
		• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
		• Observe the minimum bending radius of the cable. Lay the cable without twisting it.
		• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).

Type	Release with tool or by hand (see accessories)
Product type	Installation connector
Product family	PRC 35
Number of positions	3
Connection profile	2+PE
Locking type	Snap-in locking
Coding	AD
Insulation characteristics
Protection class	II
Degree of pollution	2

Rated voltage (III/2)	690 V
Nominal voltage ATD	690 V AC (III/2) in accordance with IEC 61984
		500 V AC (III/2) in accordance with IEC 61535/2 PfG 1915
		600 V AC / DC (III/2) In accordance with UL 2238
		500 V DC (III/2) in accordance with IEC 61535
Rated current	35 A (With 6 mm² conductor cross section in accordance with IEC 61984)
		32 A (With 6 mm² conductor cross section in accordance with IEC 61535)
		21.4 A (With 6 mm² conductor cross section and 85 °C in accordance with 2 PfG 1915)
		32 A (with AWG 10, in accordance with UL 2237)

Conductor connection
Conductor cross section	1.5 mm² ... 6 mm²

Width	37.6 mm
Height	37.6 mm
Length	105 mm
External dimensions
Outside diameter	8 mm ... 21 mm

Color	black
Color of the housing part	black
Material	EPDM
		EPDM
		PPE
		PPE
		PPE
		CuZn
Flammability rating according to UL 94	V0
Insulating material group	I / CTI 600
Seal material	EPDM
Cable seal material	EPDM
Contact material	Cu alloy
Contact surface material	silver-plated
Contact carrier material	PPE
O-ring material	EPDM
Material for screw connection	PPE
Housing material	PPE

External cable diameter	8 mm ... 21 mm
External cable diameter		8 mm ... 21 mm (For notes on cable clamping ranges, see packing slip)
Single wire, cross section	1.5 mm² 6 mm² 14 AWG 10 AWG
Stripping length of the individual wire	Lay PE conductor 8 mm leading
Halogen-free	yes

Mechanical data
Insertion/withdrawal cycles	2000 (Test specification: IEC 60512-13-2)
Insertion force	30 N ±10 N (Test specification: IEC 60512-13-2)

Ambient conditions
Degree of protection (when plugged in)	IP66 / IP68 (2m / 24h) / IP69K
Degree of protection	IP66 / IP68 (2m / 24h) / IP69K
Degree of protection		IP66 / IP68 (2m / 24h) / IP69K
Ambient temperature (operation)	-40 °C ... 105 °C (Depending on the current carrying capacity/derating curve)
Ambient temperature (storage/transport)	-40 °C ... 70 °C
Ambient temperature (assembly)	-5 °C ... 85 °C

Standards/specifications	IEC 61984:2008
		EN 61984:2008
		DIN EN IEC 61535:2020
		IEC 61535:2019
		2 PfG 1915/03.2015
		UL 2237 Ed.1:2021-01-08
		CSA C22.2 No. 182.3-16 Ed.2:2019-01