PACT RCP-4000A-UIRO-D95 - Current transformer Phoenix Contact

Mã sản phẩm: 2906231

Danh mục: PHOENIX CONTACT, Switch, Measure and Monitor Phoenix Contact,

Set consisting of a 4-way signal conditioner with screw connection technology and a Rogowski coil 300 mm in length/95 mm in diameter for AC current measurement on busbars and power lines. The signal conditioner outputs 8 different standard signals on the output side and has one switching output.

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

Product type	Current transformer
Insulation characteristics
Overvoltage category	II
Pollution degree	2

Electrical isolation	Reinforced insulation in accordance with IEC 61010-1
Typical measuring error	< 1 %
Protective circuit	Surge protection; 33 V suppressor diode
Step response (0–99%)	110 ms
Rated insulation voltage	300 V
Measuring coil
Conductor structure signal line	2x 0.22 mm (Signal (tinned))
Conductor structure signal line		1x 0.22 mm (Shielding (tinned))
Insulation	double insulation
Rated insulation voltage	1000 V AC (rms CAT III)
Rated insulation voltage		600 V AC (rms CAT IV)
Test voltage	10.45 kV DC (60 s)
Basic accuracy	<± 0.2 %
Measuring transducers
Maximum transmission error	≤ 0.5 % (From the range end value)
Frequency range	16 Hz ... 1000 Hz
Test voltage	3 kV (50 Hz, 1 min.)
General
Can be calibrated	no
Class	1
Accuracy class	1
Converter type	Rogowski coil and 4-way signal conditioner
Supply: Measuring transducers
Nominal supply voltage	24 V DC
Nominal supply voltage range	9.6 V DC ... 30 V DC
Power consumption	≤ 1 W (at I_OUT = 20 mA, 9.6 V DC, 600 Ω load)

Frequency
Designation	Measuring coil
Frequency measuring range	40 Hz ... 20000 Hz
Position error	<± 0.1 % (typical)
Linearity error	< 0.1 %
Signal
Input signal (at 50 Hz)	100 mV (1000 A)
Curve type	Sine
Input impedance	> 100 kΩ
Current transformers
Configurable/programmable	Via DIP switches
Rated frequency: Standard converter	40 Hz ... 20000 Hz
Primary rated current I_pn	0 A AC ... 100 A AC
		0 A AC ... 250 A AC
		0 A AC ... 400 A AC
		0 A AC ... 630 A AC
		0 A AC ... 1000 A AC
		0 A AC ... 1500 A AC
		0 A AC ... 2000 A AC
		0 A AC ... 4000 A AC
Can be calibrated	no
Class	1
Accuracy class	1
Converter type	Rogowski coil and 4-way signal conditioner

Switching: Transistor
Number of outputs	1
Contact type	1 N/O contact
Minimum switching voltage	1 V
Maximum switching voltage	30 V DC
Min. switching current	100 µA
Max. switching current	100 mA (at 30 V)
Signal
Designation	Measuring coil
Output signal (at 50 Hz)	100 mV (no load, at 1,000 A)
Output voltage (in no-load operation)	V_OUT = M * dI/dt
Output voltage (sinusoidal, in no-load operation)	100 mV (V_OUT = 2 * π * M * f * I (M = 0.318 μH; example: At 50 Hz; I = 1,000 A))
Accuracy class	1
Signal
Designation	Measuring transducer
Configurable/programmable	Yes
Voltage output signal	0 V ... 10 V (via DIP switch)
		2 V ... 10 V (via DIP switch)
		0 V ... 5 V (via DIP switch)
		1 V ... 5 V (via DIP switch)
		0 V ... 10.5 V (can be set via software)
Max. voltage output signal	 12.3 V
Current output signal	0 mA ... 20 mA (via DIP switch)
		4 mA ... 20 mA (via DIP switch)
		0 mA ... 10 mA (via DIP switch)
		2 mA ... 10 mA (via DIP switch)
		0 mA ... 21 mA (can be set via software)
Max. current output signal	24.6 mA
Load/output load voltage output	≥ 10 kΩ
Load/output load current output	≤ 600 Ω (20 mA)
Ripple	< 20 mV_PP
Ripple		< 20 mV_PP

Measuring transducer side
Connection method	Screw connection
Stripping length	10 mm
Screw thread	M3
Conductor cross section rigid	0.2 mm² ... 1.5 mm²
Conductor cross section flexible	0.2 mm² ... 1.5 mm²
Conductor cross section AWG	26 ... 16
Tightening torque	0.5 Nm ... 0.6 Nm

Width	6.2 mm
Height	110.5 mm
Depth	120.5 mm
Item dimensions
Width	6.2 mm
Height	110.5 mm
Depth	120.5 mm
Measuring coil
Length	300 mm
Diameter	8.3 mm ±0.2 mm
Measuring coil when installed
Diameter	95 mm
Signal line
Length	3 m

Coil material	Elastollan
Housing material	PC
Housing material		PBT

Ambient conditions
Measuring coil degree of protection	IP67 (not assessed by UL)
Measuring transducer degree of protection	IP20
Ambient temperature (operation)	-30 °C ... 80 °C (Measuring coil)
Ambient temperature (operation)		-40 °C ... 70 °C (Measuring transducer)
Ambient temperature (storage/transport)	-40 °C ... 80 °C (Measuring coil)
Ambient temperature (storage/transport)		-40 °C ... 85 °C (Measuring transducer)
Altitude	< 2000 m
Permissible humidity (operation)	5 % ... 95 % (non-condensing)

CE
Certificate	CE-compliant
UKCA
Certificate	UKCA-compliant
CMIM
Certificate	CMIM-compliant
UL, USA/Canada
Identification	UL 61010 Recognized
Note	Measuring coil
UL, USA/Canada
Identification	UL 508 Listed
Note	Measuring transducer

Noise immunity	EN 61000-6-2
Note	When being exposed to interference, there may be minimal deviations.
Electromagnetic compatibility	Conformance with EMC directive
Noise emission	EN 61000-6-4