ILB BT ADIO MUX-OMNI - Wireless set Phoenix Contact

Mã sản phẩm: 2884208

Danh mục: PHOENIX CONTACT, Tự động hóa Phoenix Contact,

Wireless MUX set, two modules with 16 digital inputs and outputs and 2 analog inputs and outputs (0 ... 20 mA, 0 ... 10 V) each, RSMA (female) antenna connection, incl. omnidirectional antennas with 1.5 m cable

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

Utilization restriction
EMC note	EMC: class A product, see manufacturer's declaration in the download area

Type	Block design
Product type	Wireless module
Product family	Inline
Application	I/O
MTTF	1458 Years (SN 29500 standard, temperature 25°C, operating cycle 21%)
		557 Years (SN 29500 standard, temperature 40°C, operating cycle 34.25%)
		219 Years (SN 29500 standard, temperature 40°C, operating cycle 100%)
MTBF	465 Years (Telcordia standard, 25°C temperature, 21% operating cycle (5 days a week, 8 hours a day))
MTBF		140 Years (Telcordia standard, 40°C temperature, 34.25% operating cycle (5 days a week, 12 hours a day))
Diagnostics messages	Short-circuit or overload of the digital outputs LED
		Wireless connection FS LED
		Logic and actuator voltage LED
		Link quality of the wireless connection 4 LEDs
Insulation characteristics
Overvoltage category	II
Pollution degree	2
Times
Switch-on time	≤ 3 s (Until the wireless connection is established)
Delay time	≤ 10 ms (Latency, typical)
Delay time		≤ 800 ms (Failsafe function for wireless interruption)

Maximum power dissipation for nominal condition	2.4 W
Supply: Module electronics
Connection method	Inline connector
Supply voltage	24 V DC
Supply voltage range	19.2 V DC ... 30.5 V DC (via power connector)
Current consumption	60 mA (Communications power at 24 V DC, 25 °C)
Current consumption		25 mA (Actuator supply, +load current Digital OUT (8 A))
Protective circuit	Polarity protection, surge protection

Analog
Input name	Analog inputs
Description of the input	Single ended
Number of inputs	2
Current input signal	0 mA ... 20 mA
Input resistance current input	50 Ω
Voltage input signal	0 V ... 10 V
Input resistance of voltage input	130 kΩ
Measured value resolution	12 bits
Protective circuit	Surge voltage; Suppressor diodes in the analog inputs, current limitation via internal protective circuit
Digital
Input name	Digital inputs
Number of inputs	16
Connection method	Spring-cage connection
Connection technology	1-conductor
Input voltage range "0" signal	< 5 V
Input voltage range "1" signal	> 15 V
Nominal input voltage U_IN	24 V DC
Typical input current per channel	2.3 mA
Input frequency	≤ 10 Hz

Analog
Output name	Analog outputs
Number of outputs	2
Protective circuit	Transient protection
DAC resolution	12 bit
Current output signal	0 mA ... 20 mA
Load/output load current output	≤ 500 Ω
Voltage output signal	0 V ... 10 V
Load/output load voltage output	≥ 2 kΩ
Digital
Output name	Digital outputs
Connection method	Spring-cage connection
Connection technology	1-conductor
Number of outputs	16
Protective circuit	Short-circuit protection, overload protection, protected against reverse voltages
Output current	8 A (Total)
Maximum output current per channel	500 mA
Nominal output voltage	24 V DC
Output current when switched off	≤ 10 µA (When not loaded, a voltage can be measured even at an output that is not set.)
Nominal load, inductive	12 VA (1.2 H, 50 Ω)
Nominal load, lamp	12 W
Nominal load, ohmic	12 W (48 Ω)
Reverse voltage resistance to short pulses	Reverse voltage proof
Behavior with overload	Auto restart
Behavior with inductive overload	Output can be destroyed
Behavior at voltage switch-off	The output follows the power supply without delay

Conductor cross section, rigid	0.2 mm² ... 1.5 mm²
Conductor cross section, flexible	0.2 mm² ... 1.5 mm²
Conductor cross section, flexible [AWG]	... 16
Stripping length	8 mm

Functions
Wireless licenses	Europe, additional countries in the e-shop
Wireless
Modulation type	GFSK (Gaussian Frequency Shift Keying)
Antenna connection method	RSMA (female)
No. of channels	40
Frequency range	2.402 GHz ... 2.48 GHz (ISM bandwidth)
Frequency band	2.4 GHz
Wireless standard	Bluetooth
Transmission power	5 dBm
Receiver sensitivity	-95 dBm

Diagnostic messages
Diagnostics	Short-circuit or overload of the digital outputs
Message	LED
Diagnostic messages
Diagnostics	Wireless connection
Message	FS LED
Diagnostic messages
Diagnostics	Logic and actuator voltage
Message	LED
Diagnostic messages
Diagnostics	Link quality of the wireless connection
Message	4 LEDs

Dimensional drawing
Width	95 mm
Height	123.4 mm
Depth	57 mm
Note on dimensions	with connectors

Material Housing

PA 6.6-FR

Ambient conditions
Ambient temperature (operation)	-25 °C ... 60 °C
Degree of protection	IP20
Air pressure (operation)	795 hPa ... 1080 hPa (up to 2000 m above sea level)
Air pressure (storage/transport)	66 kPa ... 108 kPa (up to 3500 m above sea level)
Ambient temperature (storage/transport)	-25 °C ... 85 °C
Permissible humidity (operation)	95 % (non-condensing)
Permissible humidity (storage/transport)	95 %

CE
Certificate	CE-compliant
EAC
Identification	EAC
UL, USA/Canada
Identification	508 Listed
Wireless approval, Europe
Note	RED 2014/53/EU
Wireless approval USA, FCC
Identification	YG3ADIOMUX
Note	FCC directive, part 15.247
Wireless approval India, WPC
Certificate	NR-ETA/5957
Wireless approval Japan, MIC
Identification	Japan MIC (RF) ID:202-LSF002
Wireless approval Canada, IC
Certificate	4720B-ADIOMUX
Note	ISC directive RSS 210
Wireless approval Mexico, IFT
Certificate	IFT RCPPHIL19-2130
Wireless approval South Africa, ICASA
Certificate	TA-2006/032
KC approval for South Korea
Certificate	MSIP-CRI-PCK-2884208

Electromagnetic compatibility	Conformance with EMC Directive 2014/30/EU
Electrostatic discharge
Standards/regulations	EN 61000-4-2
Electrostatic discharge
Contact discharge	± 6 kV (Test Level 3)
Discharge in air	± 8 kV (Test Level 3)
Indirect discharge	± 6 kV
Comments	Criterion B
Electromagnetic HF field
Standards/regulations	EN 61000-4-3
Electromagnetic HF field
Frequency range	26 MHz ... 3 GHz (Test Level 3)
Field intensity	10 V/m
Comments	Criterion A
Fast transients (burst)
Standards/regulations	EN 61000-4-4
Fast transients (burst)
Input	± 2 kV (Test Level 3)
Signal	± 2 kV (Signal line)
Comments	Criterion B
Surge current load (surge)
Standards/regulations	EN 61000-4-5
Surge current load (surge)
Input	± 0.5 kV (symmetrical)
Input		± 1 kV (asymmetrical)
Signal	± 1 kV (Signal line, asymmetrical)
Comments	Criterion B
Conducted interference
Standards/regulations	EN 61000-4-6
Conducted interference
Frequency range	0.15 MHz ... 80 MHz
Comments	Criterion A
Voltage	10 V
Emitted interference
Emitted radio interference in acc. with EN 55011	EN 55016-2-3 Class A industrial applications
Criteria
Criterion A	Normal operating behavior within the specified limits.
Criterion B	Temporary impairment to operational behavior that is corrected by the device itself.

Protection class	III
Free from substances that could impair the application of coating	in accordance with VW-AUDI-Seat central standard P-VW 3.10.7 57 65 0
Standards/specifications	EN 300328
		EN 61000-6-4
		EN 61000-6-2
		EN 62311
		EN 60950