IB IL SGI 2/P/EF-PAC - Analog module Phoenix Contact

Mã sản phẩm: 2702373

Danh mục: PHOENIX CONTACT, Tự động hóa Phoenix Contact,

Inline analog strain gauge input terminal, complete with accessories (connector and marking field), 2 precise and fast inputs, 4, 6-conductor connection technology

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

Dimensional drawing
Width	48.8 mm
Height	136 mm
Depth	71.5 mm

Color

green

Inline local bus
Connection method	Inline data jumper
Transmission speed	500 kbps
Transmission physics	Copper
Serial
Designation	V.24 (RS-485) serial interface
Addressing	Address 1 = Measured gross/net value
Addressing		Address 2 = Measured tare value
Termination resistor	120 Ω
Transmission protocol	STX/ETX

Module
ID code (dec.)	223
ID code (hex)	DF
Length code (hex)	03
Length code (dec)	03
Process data channel	48 bit
Input address area	6 Byte
Output address area	6 Byte
Register length	64 bit
Required parameter data	23 Byte
Required configuration data	5 Byte

Analog
Description of the input	Input channels for strain gauge
Number of inputs	2
Connection technology	6 or 4-wire, twisted pair shielded cable
Bridge difference U_d	Measuring range specified by selecting the characteristic
Bridge voltage U₀	5 V
Measured value representation	16 bit, 20 bit, ASCII data record
Characteristics	±1 mV/V, ±2 mV/V, ±3 mV/V, ±3.33 mV/V, ±4 mV/V, ±5 mV/V, ±6 mV/V, manual characteristic value specification
Contacts
Description	Floating N/O contact
Quantity	2 (K_a1-K_b1, K_a2-K_b2)
Contact resistance	< 1 Ω (typical)
Contact resistance		3 Ω (maximum)
Typical response time	typ. 0.2 ms (opening)
Typical response time		typ. 2 ms (close)

Analog
Output description	Jumper supply
Number of outputs	2
Impedance	> 43 Ω (per channel)
Output voltage	typ. 5 V
Output current	max. 115 mA (per channel)

Type	modular
Product type	I/O component
Product family	Inline
Operating mode	Process data operation with 3 words, PCP with 1 word
Diagnostics messages	Failure of the power supply at U_ANA Error message in the process data
		Failure of or insufficient communications power U_L I/O error message sent to the bus coupler
		I/O error Error message in the process data

Potentials
Power consumption	typ. 1.4 W (Device in nominal operation)
Power consumption		max. 3.5 W (Device with maximum load)
Potentials: Communications power (U_L)
Supply voltage	7.5 V DC (via voltage jumper)
Current draw	max. 95 mA
Current draw		typ. 80 mA
Potentials: Supply of analog modules (U_ANA)
Supply voltage	24 V DC (via voltage jumper)
Supply voltage range	19.2 V DC ... 30 V DC (including all tolerances, including ripple)
Current draw	typ. 32 mA (in case of typical load of 350 Ohm per channel)
		115 mA (with maximum load of 43 Ω and display)
		14 mA (for no-load operation without strain gauge or display)

Connection technology
Connection name	Inline connector
Conductor connection
Connection method	Spring-cage connection
Conductor cross section rigid	0.08 mm² ... 1.5 mm²
Conductor cross section flexible	0.08 mm² ... 1.5 mm²
Conductor cross section AWG	28 ... 16
Stripping length	8 mm
Inline connector
Connection method	Spring-cage connection
Conductor cross section, rigid	0.08 mm² ... 1.5 mm²
Conductor cross section, flexible	0.08 mm² ... 1.5 mm²
Conductor cross section AWG	28 ... 16
Stripping length	8 mm

Ambient conditions
Ambient temperature (operation)	-25 °C ... 55 °C
Degree of protection	IP20
Air pressure (operation)	70 kPa ... 106 kPa (up to 3000 m above sea level)
Air pressure (storage/transport)	70 kPa ... 106 kPa (up to 3000 m above sea level)
Ambient temperature (storage/transport)	-25 °C ... 85 °C
Permissible humidity (operation)	10 % ... 95 % (non-condensing)
Permissible humidity (storage/transport)	10 % ... 95 % (non-condensing)