HC-M-02-AT-M-10 - Contact insert module Phoenix Contact

Mã sản phẩm: 1417389

Danh mục: PHOENIX CONTACT, Kết nối (Connect) Phoenix Contact 2,

Contact insert module, number of positions: 2, power contacts: 2, control contacts: 0, Pin, Axial screw connection, 690 V, 40 A, 2.5 mm2 ... 10 mm2, application: Power

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

General	For HEAVYCON HC-B6 to B48 housing, snap-in module frame required, axial connection for 2 mm Allen key
General	Connectors may be operated only when there is no load/voltage.
General	The axial screw connection must be established using a 2 mm Allen key (for stranded conductors only)

Assembly instructions	To ensure correct use, installation in housing with IP54 protection or better is required
Assembly instructions		Note regarding axial connection technology: Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used. Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use. The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use. Assembly instructions Before assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque.

Product type	Modular contact insert
Number of positions	2
Connection profile	2
Application	Power
Number of module slots	1
No. of power contacts	2
No. of control contacts	0
Series	HC-M-02
Insulation characteristics
Overvoltage category	III
Degree of pollution	3

Connection technology
Connection technology	Axial screw connection
Connection in acc. with standard	IEC / EN
Conductor connection
Conductor cross section	2.5 mm² ... 10 mm² (The cross section specification refers to the geometric cross section of the cable used)
Connection cross section AWG	12 ... 10
Tightening torque	1.5 Nm (2.5 mm² ... 4 mm²)
Tightening torque		2 Nm (6 -8 mm²)
Stripping length of the individual wire	10 mm +0.5 mm (2.5 mm² ... 4 mm²)
		10 mm +0,5 mm (4 mm²)
		10 mm +0,5 mm (10 mm²)

Dimensional drawing
Width	34.2 mm
Height	34.7 mm
Length	14.6 mm
Mechanical characteristics
Contact diameter	4 mm

Rated voltage (III/2) contacts	1000 V
Rated voltage (III/3)	690 V
Rated surge voltage (III/2)	8 kV
Rated surge voltage (III/3)	8 kV
Rated surge voltage	8 kV
Rated current	40 A

Mechanical data
Insertion/withdrawal cycles	≥ 500

Color	light grey
Flammability rating according to UL 94	V0
Contact material	Copper alloy
Contact surface material	Ag
Contact carrier material	PC
Standards/regulations	PC: Fire protection in rail vehicles - requirement sets R22, R23, and R24 acc. to DIN EN 45545-2 (Risk level HL1 - HL3)