HC-K 6/12-EBUS - Contact insert Phoenix Contact

Mã sản phẩm: 1636363

Danh mục: PHOENIX CONTACT, Kết nối (Connect) Phoenix Contact 2,

Contact insert, number of positions: 6+12+PE, size: B16, power contacts: 6, control contacts: 12, Socket, Axial screw connection, 690 V, 40 A, 2.5 mm2 ... 10 mm2, application: Power/signal

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

General	For HEAVYCON ADVANCE and HEAVYCON housing of type B16/B32, axial connection for 2 mm Allen wrench
General	Connectors may be operated only when there is no load/voltage.
General	The axial screw connection must be established using a 2 mm Allen key (for stranded conductors only)

Assembly instructions	To ensure correct use, installation in housing with IP54 protection or better is required
Assembly instructions		Note regarding axial connection technology: Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used. Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use. The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use. Assembly instructions Before assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque.
Connection method	Screw connection

Type	B16
Type		B32
Product type	Contact insert with a fixed no. of positions
Number of positions	18
Connection profile	6+12+PE
Contact numbering	1 - 6 (power contacts)
Contact numbering		11 - 22 (control contacts)
Application	Power/signal
No. of power contacts	6
No. of control contacts	12
Contact type	turned
Series	HC-K
Screwdriver blade	0.5 x 3.5 mm (control contacts)
Insulation characteristics
Overvoltage category	III
Degree of pollution	3

Dimensional drawing
Width	34 mm
Height	47 mm
Length	84.1 mm
Drill hole distance, horizontal	77.5 mm
Mechanical characteristics
Contact diameter	4 mm

Connection technology
Connection technology	Axial screw connection (power contacts)
Connection technology		Screw connection (control contacts)
Conductor connection
Conductor cross section	2.5 mm² ... 10 mm² (power contacts)
Conductor cross section		0.2 mm² ... 2.5 mm² (control contact)
Connection cross section AWG	12 ... 8 (power contacts)
Connection cross section AWG		24 ... 14 (control contacts)
Tightening torque	2 Nm ... 2.5 Nm (PE connection)
		0.5 Nm ... 0.8 Nm (Mounting screws for mounting in the HEAVYCON housing)
		0.5 Nm ... 0.8 Nm (control contacts)
		1.5 Nm (Power 2.5 mm² ... 4 mm²)
		2 Nm (Power 6 mm² ... 10 mm²)
Stripping length of the individual wire	8 mm +1 mm (Power 6 mm² ... 10 mm²)
		10 mm (Signal)
		5 mm +1 mm (Power 2.5 mm² ... 4 mm²)

Rated voltage (III/3)	690 V
		230 V (Conductor-PE)
		400 V (Signal contacts, conductor-conductor)
Rated voltage for power contacts	230/400 V
Rated surge voltage	8 kV (power contacts)
Rated surge voltage		4 kV (control contacts)
Rated current	40 A (power contacts)
Rated current		10 A (control contacts)

Mechanical data
Insertion/withdrawal cycles	≥ 500

Flammability rating according to UL 94	V0
Contact material	Cu alloy
Contact carrier material	PC
Material of contact surface, power contact	Ag
Material of contact surface, control contact	Ag