HC-HS 2-D7-ESTS - Contact insert Phoenix Contact

Mã sản phẩm: 1586277

Danh mục: PHOENIX CONTACT, Kết nối (Connect) Phoenix Contact 2,

Contact insert, number of positions: 2+PE, size: D7, power contacts: 2, Pin, Axial screw connection, 400 V, 40 A, 4 mm2 ... 10 mm2, application: Power

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

General	for HC-D7 housing, axial connection 2.0 mm, Allen key
General	Connectors may be operated only when there is no load/voltage.
General	The axial screw connection must be established using a 2 mm Allen key (for stranded conductors only)

Assembly instructions	To ensure correct use, installation in housing with IP54 protection or better is required
Assembly instructions		Note regarding axial connection technology: Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used. Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use. The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use. Assembly instructions Before assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque.

Type	D7
Product type	Contact insert with a fixed no. of positions
Number of positions	2
Connection profile	2+PE
Contact numbering	1 - 2
Application	Power
No. of power contacts	2
Contact type	turned
Series	HC-HS
Insulation characteristics
Overvoltage category	III
Degree of pollution	3

Dimensional drawing
Width	21 mm
Height	40 mm
Length	21 mm
Mechanical characteristics
Contact diameter	4 mm

Connection technology
Connection technology	Axial screw connection
Connection in acc. with standard	IEC / EN
Conductor connection
Conductor cross section	4 mm² ... 10 mm² (The cross section specification refers to the geometric cross section of the cable used)
Connection cross section AWG	10 ... 8
Tightening torque	0.5 Nm ... 0.8 Nm (Mounting screws for mounting in the HEAVYCON housing)
Tightening torque		1.8 Nm
Stripping length of the individual wire	8 mm +1 mm

Rated voltage (III/3)	400 V
Rated surge voltage	6 kV
Rated current	40 A

Mechanical data
Insertion/withdrawal cycles	≥ 500

Flammability rating according to UL 94	V0
Seal material	NBR
Contact material	Copper alloy
Contact surface material	Ag
Contact carrier material	PC

Ambient conditions
Ambient temperature (operation)	-40 °C ... 125 °C (including heating up of contacts)

Constructional and testing regulations	DIN VDE 0627/86
		DIN VDE 0110/02.79
		DIN VDE 0110-1/04.97
		IEC 60664-1, DIN IEC 60512
		IEC 60352
Tests	DIN VDE 0627/86
		DIN VDE 0110/02.79
		DIN VDE 0110-1/04.97
		IEC 60664-1, DIN IEC 60512
		IEC 60352