HC-COM-Q4/2-I-AT/PT-M - Contact insert Phoenix Contact

Mã sản phẩm: 1079558

Danh mục: PHOENIX CONTACT, Kết nối (Connect) Phoenix Contact 2,

Contact insert, number of positions: 4+2+PE, size: COM, power contacts: 4, control contacts: 2, number of connections per position: 1, Pin, Axial screw connection, 400 V, 40 A, 2.5 mm2 ... 6 mm2, application: Power/signal

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

General

Connectors may be operated only when there is no load/voltage.

Assembly instructions	To ensure correct use, installation in housing with IP54 protection or better is required
Assembly instructions		Note regarding axial connection technology: Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used. Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use. The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use. Assembly instructions Before assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque.
Hexagonal socket	WAF 2

Type	COM
Product type	Contact insert with a fixed no. of positions
Number of positions	6
Connection profile	4+2+PE
Contact numbering	1 - 4 (power contacts)
Contact numbering		11 - 12 (control contacts)
Application	Power/signal
Number of connections per position	1
No. of power contacts	4
No. of control contacts	2
Contact type	turned
Series	HC-COM
Insulation characteristics
Overvoltage category	III
Degree of pollution	3

Dimensional drawing
Width	22.5 mm
Height	48 mm
Length	42 mm
Mechanical characteristics
Contact diameter	4 mm

Connection technology
Connection technology	Axial screw connection (power contacts)
Connection technology		Push-in connection (control contacts)
Number of connections per position	1
Connection in acc. with standard	IEC / EN
Conductor connection
Conductor cross section	2.5 mm² ... 6 mm² (power contacts)
Conductor cross section		0.34 mm² ... 1.5 mm² (Control contacts, applies to flexible conductors with ferrules)
Connection cross section AWG	14 ... 10 (power contacts)
Connection cross section AWG		22 ... 16 (Control contacts, applies to flexible conductors with ferrules)
Tightening torque	1.5 Nm ... 1.8 Nm (2,5 mm² ... 6,0 mm²)
Stripping length of the individual wire	9 mm +1 mm (Power)
Stripping length of the individual wire		8 mm (Signal)

Rated voltage (III/3)	400 V (Phase-ground power contacts)
		250 V (control contacts)
		690 V (Phase-phase power contacts)
Rated voltage for power contacts	400/690 V
Rated voltage for power contacts		250
Rated surge voltage	6 kV (Phase-phase power contacts)
Rated surge voltage		4 kV (control contacts)
Rated current	40 A (power contacts)
Rated current		10 A (control contacts)

Mechanical data
Insertion/withdrawal cycles	≥ 500

Flammability rating according to UL 94	V0
Seal material	NBR
Contact material	Copper alloy
Contact surface material	Ag (alternatively Au)
Contact carrier material	PC
Material of contact surface, power contact	Ag
Material of contact surface, control contact	Ag (alternatively Au)
Standards/regulations	PC: Fire protection in rail vehicles - requirement sets R22, R23, and R24 acc. to DIN EN 45545-2 (Risk level HL1 - HL3)