FLKM-D37SUB/M/MT/16M/ETHA - Interface module Phoenix Contact

Mã sản phẩm: 1274077

Danh mục: PHOENIX CONTACT, Kết nối (Connect) Phoenix Contact,

VARIOFACE termination board for Siemens SIMATIC® ET 200SP HA, with specific marking, with knife-disconnect terminal block and test point, as well as power supply terminal blocks

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

General	The necessary requirements for insulation (basic insulation or reinforced insulation) from adjacent modules (in DIN-rail direction) must be realized by applying suitable measures (e. g., partition plates).
General	Only mount the device on DIN rails according to DIN EN 60715.
General	Install the module in housing with IP54 degree of protection in accordance with EN 60529. The stated limits concerning mechanical or thermal loads on the module must not be exceeded.
General	No additional touch protection is required when using a SELV/PELV voltage (≤30 V AC or 60 V DC).
General	All input and output lines are dimensioned according to the maximum output current of the device or separately protected.
General	The device may not be cleaned at all, or only dry-cleaned.
General	The max. load current must not be exceeded by the total current of all connected conductors.
General	Connectors may be operated only when there is no load/voltage.
General	Take measures outside the device to limit transient surge voltages to the respective value for overvoltage category II.
General	Only use the device in accordance with its intended use. Non-compliant applications can result in injury or damage to property.
General	The installation and startup of this device may only be performed by an electrically skilled person. Observe the applicable national standards and regulations.
General	Only use SELV or PELV power supply units or power supplies to supply the device.
General	Ensure that the device’s 24 V supply voltage and the I/O module have a shared reference potential (GND).

Product type	Interface module
No. of channels	8
No. of channels		16
Insulation characteristics
Insulation	Functional insulation
Insulation characteristics: Air clearances and creepage distances
Insulation	Functional insulation
Overvoltage category	II
Pollution degree	2

No. of channels	816
Max. permissible operating voltage	30 V DC (SELV/PELV)
Max. permissible current	1 A (per branch)
Max. permissible total current	2 A (per module)
Air clearances and creepage distances
Rated insulation voltage	63 V
Rated surge voltage	0.8 kV (1.2/50 μs)
Supported controller SIEMENS ET 200SP HA
Suitable I/O module	6DL1131-6BH00-0PH1 (Terminal Block H1/M1)
		6DL1132-6BH00-0PH1 (Terminal Block H1/M1)
		6DL1134-6JH00-0PH1 (Terminal Block H1/M1)
		6DL1134-6TH00-0PH1 (Terminal Block H1/M1)

Field level
Connection method	Screw connection with disconnect knife
Number of positions	36
Conductor cross section rigid	0.2 mm² ... 4 mm²
Conductor cross section flexible	0.2 mm² ... 4 mm²
Conductor cross section AWG	24 ... 12
Controller level
Connection in acc. with standard	IEC 60807-2
Connection in acc. with standard		DIN 41652
Connection method	D-SUB pin strip
Screw thread	UNC 4-40
Number of connections	1
Number of positions	37

Status display present

Width	169 mm
Height	77 mm
Depth	50.5 mm

Ambient conditions
Degree of protection	IP00
Degree of protection (Installation location)	≥ IP54
Ambient temperature (operation)	-20 °C ... 70 °C
Altitude	≤ 2000 m