FLKM 20-PA-ET200SP - Front adapters Phoenix Contact

Mã sản phẩm: 1099751

VARIOFACE front adapter for Siemens SIMATIC® ET200SP, with a 20-pos. FLK-/IDC male strip, max. 16 channels can be connected

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Product type	Front adapter
Insulation characteristics
Insulation	Functional insulation
Insulation characteristics: Air clearances and creepage distances
Insulation	Functional insulation
Overvoltage category	II
Pollution degree	2

Max. permissible operating voltage	60 V DC
Max. permissible current	1 A (per path)
Max. permissible total current	2 A (per byte when supplying from the module side)
		8 A (When supplying via the front adapter)
		2 A (UL)
Nominal operating mode	100% operating factor
Air clearances and creepage distances
Rated insulation voltage	63 V
Rated surge voltage	0.6 kV
Supported controller SIEMENS ET 200SP
Suitable base unit	6ES7193-6BP00-0BA0
		6ES7193-6BP00-2BA0
		6ES7193-6BP00-0BA1
		6ES7193-6BP00-0DA0
		6ES7193-6BP00-2DA0
		6ES7193-6BP00-0DA1
Suitable I/O module	6ES7131-6BH01-0BA0 (Base Units A0/A1)
		6ES7131-6BH01-2BA0 (Base Units A0/A1)
		6ES7132-6BH01-0BA0 (Base Units A0/A1)
		6ES7132-6BH01-2BA0 (Base Units A0/A1)
		6ES7134-6GD01-0BA1 (Base Units A0/A1)
		6ES7134-6GD01-2BA1 (Base Units A0/A1)
		6ES7134-6HD01-0BA1 (Base Units A0/A1)
		6ES7134-6HD01-2BA1 (Base Units A0/A1)
		6ES7134-6TD00-0CA1 (Base Units A0/A1)
		6ES7134-6JD00-0CA1 (Base Units A0/A1)
		6ES7134-6JD00-2CA1 (Base Units A0/A1)
		6ES7134-6FF00-0AA1 (Base Units A0/A1)
		6ES7134-6GF00-0AA1 (Base Units A0/A1)
		6ES7134-6JF00-0CA1 (Base Units A0/A1)
		6ES7134-6JF00-2CA1 (Base Units A0/A1)
		6ES7134-6FB00-0BA1 (Base Units A0/A1)
		6ES7134-6GB00-0BA1 (Base Units A0/A1)
		6ES7134-6HB00-0CA1 (Base Units A0/A1)
		6ES7134-6HB00-0DA1 (Base Units A0/A1)
		6ES7135-6FB00-0BA1 (Base Units A0/A1)
		6ES7135-6GB00-0BA1 (Base Units A0/A1)
		6ES7135-6HB00-0CA1 (Base Units A0/A1)
		6ES7135-6HB00-0DA1 (Base Units A0/A1)
		6ES7135-6HD00-0BA1 (Base Units A0/A1)

Controller level
Connection method	Plug-in connection
Number of connections	1
Number of positions	18
Field level
Connection method	IDC/FLK pin strip
Number of connections	1
Number of positions	20
Supply
Connection method	Push-in spring connection
Number of connections	1
Number of positions	2
Conductor cross section rigid	0.14 mm² ... 1.5 mm²
Conductor cross section flexible	0.14 mm² ... 1.5 mm²
Conductor cross section AWG	26 ... 16

Width	15 mm
Height	53 mm

Ambient conditions
Degree of protection	IP00
Degree of protection (Installation location)	≥ IP54 (Installation location)
Ambient temperature (operation)	-20 °C ... 60 °C
Altitude	≤ 2000 m

UL, USA/Canada
Identification	UL 508 Recognized

Air clearances and creepage distances
Standards/regulations	DIN EN 50178

General	Once plugged in, the front adapter and terminal block form a single unit that can no longer be separated.
General	No additional touch protection is required when using a SELV/PELV voltage (≤ 25 V AC or 60 V DC).
General	Against adjacent modules in the support rail direction at least one functional insulation on the output-side is complied with. If the application has higher requirements on the insulation (basic insulation or reinforced insulation), then these must be realized through suitable measures (e. g. partition plates).