EXTENDER 2010 ETH COAX-G - Ethernet extenders Phoenix Contact

Mã sản phẩm: 1319320

Danh mục: PHOENIX CONTACT, Tự động hóa Phoenix Contact,

Gigabit Ethernet extender, network extension with coaxial cable up to 1 kilometer and bandwidth up to 1 Gbps, Power over Link function (PoL) for the power supply of additional devices via the coaxial cable, Power over Ethernet function (PoE)

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

Product type	Ethernet extenders
MTTF	293 Years (SN 29500 standard, temperature 25°C, operating cycle 21%)
		134 Years (SN 29500 standard, temperature 40°C, operating cycle 34.25%)
		55 Years (SN 29500 standard, temperature 40°C, operating cycle 100%)
Insulation characteristics
Pollution degree	2

Functionality
Basic functions	Gigabit Ethernet extender in accordance with ITU G.9960

Electrical isolation	VCC (US+GND) // Ethernet (PoE) // G.hn (without PoL) // FE
Mains type	Permanent line
Test voltage data interface/power supply	1.5 kV AC (50 Hz, 1 min.)
Supply
Supply voltage range	18 V DC ... 57 V DC
Nominal supply voltage	24 V DC (Without PoL, without PoE)
Nominal supply voltage		48 V DC (With PoL or with PoE)
Power consumption	≤ 7.5 W (Without PoL, without PoE)
		≤ 37.5 W (Without PoL, with PoE)
		≤ 37.5 W (With PoL, without PoE)
		≤ 82.5 W (With PoL, with PoE)
Protective circuit	Overload protection, protection against polarity reversal; Internal device protection: 2x 5 AF, internal series diode
Connection method	Push-in spring connection

Supply
Connection method	Push-in spring connection
Conductor cross section flexible, with ferrule without plastic sleeve	0.2 mm² ... 4 mm²
Conductor cross section, flexible, with ferrule, with plastic sleeve	0.2 mm² ... 4 mm²
2 conductors with the same cross section, flexible, with TWIN ferrule with plastic sleeve	0.5 mm² ... 1.5 mm²
Conductor cross section, flexible	0.20 mm² ... 6.00 mm²
Conductor cross section, rigid	1.00 mm² ... 6.00 mm²
Conductor cross section, flexible [AWG]	24 ... 10
Stripping length	10 mm

Signal	Ethernet
Basic functions	Gigabit Ethernet extender in accordance with ITU G.9960
Data: Ethernet interface, 10/100/1000Base-T(X) in accordance with IEEE 802.3
Serial transmission speed	10/100/1000 Mbps
Connection method	RJ45 jack, shielded
No. of channels	1
Transmission length	< 100 m (shielded twisted pair)
Protocols supported	Protocol-transparent for TCP/IP, IPv4, and IPv6
Maximum output power	15 W (at ≤55°C)
Maximum output power		30 W (at ≤50°C)
Data: G.hn interface in accordance with ITU G.9960
Transmission speed	≤ 1000 Mbps (Depending on the quality of the data line)
Connection method	BNC female connector for coaxial cables
Transmission length	≤ 1000 m (Depending on the quality of the data line)
Transmission method	QAM (quadrature amplitude modulation) carrier frequency method
Output power	≤ 91 W (With PoL)

Dimensional drawing
Width	23 mm
Height	101 mm
Depth	115 mm

Material Housing	PA 6.6-FR
Flammability rating according to UL 94	V0

Ambient conditions
Degree of protection	IP20
Ambient temperature (operation)	-40 °C ... 60 °C (Free standing, without PoE)
		-40 °C ... 55 °C (Free standing, PoE up to 15 W)
		-40 °C ... 50 °C (Free standing, PoE up to 30 W)
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Altitude	≤ 2000 m
Permissible humidity (operation)	10 % ... 95 % (non-condensing)
Permissible humidity (storage/transport)	10 % ... 95 % (non-condensing)

CE
Certificate	CE-compliant
Corrosive gas test
Identification	ISA-S71.04-1985 G3 Harsh Group A

Noise immunity	EN 55035
Electromagnetic compatibility	Conformance with EMC Directive 2014/30/EU
Noise emission	EN 61000-6-4, Class A, industrial area of application
Electrostatic discharge
Standards/regulations	EN 61000-4-2
Electrostatic discharge
Contact discharge	± 6 kV
Discharge in air	± 8 kV
Indirect discharge	± 6 kV
Comments	Criterion B
Electromagnetic HF field
Standards/regulations	EN 61000-4-3
Electromagnetic HF field
Frequency range	80 MHz ... 3 GHz (80% amplitude modulation with 1 kHz)
Field intensity	10 V/m
Frequency range	3 GHz ... 6 GHz (80% amplitude modulation with 1 kHz)
Field intensity	3 V/m
Comments	Criterion A
Fast transients (burst)
Standards/regulations	EN 61000-4-4
Fast transients (burst)
Input	± 2.2 kV
Signal	± 2.2 kV (Ethernet, G.hn)
Surge current load (surge)
Standards/regulations	EN 61000-4-5
Surge current load (surge)
Input	± 0.5 kV (Symmetrical, unshielded supply line)
Input		± 1 kV (Asymmetrical, unshielded supply line)
Signal	± 1 kV (Ethernet signal / asymmetrical: shielded Ethernet cable)
		± 4 kV (Ethernet signal / asymmetrical: cable to ground, unshielded G.hn cable)
		± 2 kV (Ethernet signal / symmetrical: cable to cable, unshielded G.hn cable)
		± 4 kV (Telecommunication lines, symmetrical, unshielded, with primary protection)
		± 1 kV (Telecommunication lines, symmetrical, unshielded, without primary protection)
Comments	Criterion B
Conducted interference
Standards/regulations	EN 61000-4-6
Conducted interference
Frequency range	0.15 MHz ... 80 MHz (80% amplitude modulation with 1 kHz)
Comments	Criterion A
Voltage	10 V
Criteria
Criterion A	Normal operating behavior within the specified limits.
Criterion B	Temporary impairment to operational behavior that is corrected by the device itself.

Mounting type	DIN rail mounting
Assembly instructions	To allow for air circulation, mount the device freestanding, with a clearance of at least one centimeter on all sides to other devices.
Mounting position	Vertical (horizontal DIN rail)