CHARX PS-M2/3AC/1000DC/30KW - DC power module Phoenix Contact

Mã sản phẩm: 1232243

Danh mục: PHOENIX CONTACT, Supply, charge, and protect Phoenix Contact,

CHARX power basic, Fast charging module for setting up DC charging stations, 19" rack mounting, CAN bus, input: 3-phase, output: 150 V DC...1000 V DC / 0 A...100 A

Liên hệ mua hàng

Hãng sản xuất: PHOENIX CONTACT

Chất lượng: Mới 100%

Bảo hành: Chính hãng

Chứng từ: CO/CQ, hóa đơn VAT

Liên hệ(SĐT/Zalo): 0933612627

Mô tả

AC operation
Input voltage range	3x 320 V AC ... 530 V AC
Nominal input voltage range	3x 400 V AC ... 480 V AC -20 % / +10 %
Input frequency	3x 50 Hz 60 Hz ±10 %
Input current	3x 54 A (340 V AC)
Input current		3x 35 A (530 V AC)
Inrush current limitation	< 60 A
Power factor (cos phi)	0.99
Total distortion (THDi)	< 5 % (50% ... 100% output load)
Insulation resistance	> 10 MΩ
Supply system configuration	Star network (TN, TT, IT (PE))

Efficiency	> 95 % (P_Out >50%)
Output voltage range	150 V DC ... 1000 V DC
Output current range	0 A ... 100 A
Output current residual ripple	≤ 1 %
Nominal power	30 kW
Power dissipation standby	< 14 W
Protection against overvoltage at the output (OVP)	> 1040 V DC
Derating	> 45 °C ... 55 °C (1.2 A/K)
		> 55 °C (3.2 A/K)
		> 55 °C (1 kW/K)
Control deviation	< 0.5 % (Voltage deviation static load change 20% ... 100%)
		< 1 % (Current deviation Static load change 20 % ... 100 %)
		± 0.2 % (Input voltage change ±20 %)
Switch-on delay	< 8 s
Overshoot behavior	± 3 % (Switch-on procedure)

Input
Designation	Input
Identification	AC IN: L1 / L2 / L3 / PE
Conductor connection
Connection method	Push-lock connection
rigid	2.5 mm² ... 10 mm²
flexible	2.5 mm² ... 25 mm²
rigid (AWG)	12 ... 6 (Cu)
Stripping length	18 mm (rigid/flexible)
Output
Designation	Output
Identification	DC OUT: + / -
Conductor connection
Connection method	T-LOX knee lever connection
rigid	10 mm² ... 50 mm²
rigid		25 mm² (recommended)
flexible	16 mm² ... 50 mm²
flexible		25 mm² (recommended)
rigid (AWG)	4 ... 1 (Cu)
Stripping length	18 mm (10 mm² ... 25 mm²)
Stripping length		20 mm (35 mm² ... 50 mm²)

Interface	CAN bus
Number of interfaces	1
Connection method	2x RJ45 (pin assignment, CANopen standard)
Locking	Locking clip
Transmission physics	Twisted-Pair
Topology	Line (daisy-chain connection)
Transmission speed	125 kbps
Transmission length	max. 20 m
Supported protocols	CAN 2.0B
Electrical isolation	yes (primary/secondary)
Electrical isolation		no (PE)
Number of power modules as CAN bus devices	max. 48 (within one CHARX control controller)
Termination resistor	120 Ω (Terminating the end device)

Number of phases	3
Electrical isolation between input and output	yes
Insulation voltage input/output	2121 V DC
Insulation voltage input, output / housing	2121 V DC
Insulation voltage input, output/signal, communication	4242 V DC
Insulation voltage signal, communication/housing	707 V DC

Product type	DC power module
Product family	CHARX power basic
MTBF (IEC 61709, SN 29500)	> 300000 h
Service life	40000 h (40 °C)
Service life		70000 h (Fan)
Hot PLUG connection	No
Ventilation	No
Internal fan	yes
Flow direction	from front to back
Insulation characteristics
Protection class	I
Pollution degree	2

Dimensional drawing
Width	483 mm
Height	134 mm
Depth	550 mm
Rack unit	3 U

Mounting type

19" rack mounting

Housing material

Zn-Al alloy

Ambient conditions
Degree of protection	IP20
Ambient temperature (operation)	-40 °C ... 70 °C
Ambient temperature (storage/transport)	-40 °C ... 70 °C
Overtemperature protection (OTP)	> 75 °C
Maximum altitude	≤ 4000 m (Derating >2000 m: 10% / 1000 m)
Permissible humidity (operation)	≤ 95 % (non-condensing)
Noise level	< 60 dB (1 m)

Overvoltage category
IEC 60664-1	II
Electric vehicle conductive charging system - Part 1: General requirements
Standards/specifications	IEC 61851-1
Electric vehicle conductive charging system – Part 23: DC electric vehicle charging station
Standards/specifications	IEC 61851-23
Standard for Safety for Electric Vehicle (EV) Charging System Equipment
Standards/specifications	ANIS/UL 2202